Stock Control Arm Removal

1. Park your car in a flat, level area and allow it to cool down properly.
   
   
2. Jack your car up and support it properly, either using a lift, ramps, or jack and jack stands.
   
   
3. Lay a blanket or cardboard down under the car, or grab a creeper.  In this case his name is Andrew
   
   
   
   
   
4. Remove the front wheels of the car to get easy access to the areas we'll be working on.
   
   
   
   
   
5. Moving to the front end link where it meets the control arm, use a 17mm wrench to undo the nut while using a m6 allen wrench to hold the center of the endlink and keep it from spinning.  Break each side loose first (sway bar and control arm) and then remove the nut completely.  Repeat with the other side.
   
    
   
   
   
   
6. On the bottom of the spindle straighten the cotter pin and remove it from the ball joint/castle nut.
   
   
   
   
   
7. Break the nut loose using a 19mm socket but leave it installed loosely for now.
   
   
   
8. With the nut still holding it inplace on the bottom gently tap downwards on the control arm to remove the ball joint from the spindle control arm.  In some cases if it's fairly rusty (ours was).  Eventually it should come free.  Now is a good time to clean out any rust in this area and coat it with a thin layer of lithium grease or similar to prevent rust in the future.  If it isn't coming free, tap gently upwards on the nut to push the balljoint up.
   
   
   
   
   
9. Undo the 3 19mm bolts and single 17mm bolt holding the rear control arm support bracket in place.
   
       
   
       
   
   
   
10. Remove the nut and bolt holding the front control arm bushing to the chassis using your 17mm socket and wrench.
    
    
    
    
    
11. If the tapered cone came off with the ball joint you'll need to remove it in order to use the new one for the COBB Control arm.  It can be a pain to remove these if they're rusted to the ball joint so using a pry bar, pickle fork or hydraulic press can help.  You may need to remove it from the car to get it off.  It's also just a good time to replace these if they haven't been done.
    
    
    
    
    
    
    
    
    

Decide Your Needs

The control arms can be installed in a variety of positions using the supplied spacers.  This will adjust the way the vehicle handles, in some cases quite drastically.  Typically we recommend installing the arms (at least to start) in the "OEM" position.  From there make changes as you need.

Installation

1. Start by installing the rear upward facing bushing onto the car using the spacers from the previous step.  It's best to get things in place but leave it loose for now.
   
       
   
   
   
2. Reinstall the front horizontal bushing with the bolt going in towards the rack.
   
   
   
   
   
3. At this point the outer balljoint should fall into place on the control arm if you just swing it upwards.  Sometimes lifting the spindle a little bit can help it drop into place.
   
   
   
   
   
4. From here you can torque snug the control arm and control arm bracket bolts down, and reinstall the cotter pin for the ball joint castle nut.  Tighten it to 36.9 ft-lb or 50N-M
   
   
5. Loosely install the sway bar end link on one side before installing it on the other side.  Then tighten them both back up to 44.3 ft-lb (60Nm)
   
   
6. In order to prevent any bushing binding we want to wait and torque the control arm down while the weight is resting on the vehicle's wheels.  This can be done by either jacking up on the control arm to put weight on the suspension, or by reinstalling the wheels and setting the car on a wheel support or ramp.  Either way make sure to keep the vehicle properly balanced and supported while doing this.
   
   
7. With the vehicle resting on it's own weight, it's time to torque the control arm down properly.  The front horizontal bushing gets torqued to 70 ft-lb (95 Nm).
   
   
8. The main vertical 19mm bolt going through the rear bushing gets tightened to 103.3 ft-lb (140Nm)
   
   
9. The two shorter 19mm bolts for the rear bushing bracket get tightened to 110 ft-lb (100Nm)
   
   
10. The 17mm bolt for the support brace going to the rear bushing support bracket gets tightened to 73.8 ft-lb (100 Nm)
    
    
11. Take your vehicle to get an allignment before any hard driving or driving at speed.