Open

8A1400 - Audi / Volkswagen Coolant Reroute Kit

Golf R 2015-23
GTI 2015-20
A7 Jetta GLI 2020
Audi A3 2.0 2015-20Audi A3 1.8 2015-2016
Audi S3 2016-20202015-2018 Golf
2015-2019 Golf Sportwagen
2017-2018 Golf Sportwagen 4Motion
2017-2019 Golf Alltrack

Congratulations on your purchase of the COBB Tuning Coolant Reroute Kit! The following instructions will assist you through the installation process. Please read them BEFORE beginning the install to familiarize yourself with the steps and tools needed. If you feel you cannot properly perform this installation, we HIGHLY recommend you take the vehicle to a qualified and experienced automotive technician.

Remove the OEM Volkswagen Intake

Before removal of factory intake, it is recommended to remove the engine cover by pulling it off of its grommets.

1. Inspect the new components included with the COBB kit. If anything appears out of place, please contact COBB immediately and do not proceed with the installation.
   
   

2. Park your car in a flat, level area.

    

   Open

   

   
   
   

3. Using the hose clamp pliers, take off the clamp holding the stock intake tube to the turbo.  Then pull the tube off of the turbo inlet housing. 
   
   

   
   
   

4. Take a T20 Torx screwdriver and remove the screws holding the stock snorkel in place. 
   
   

   
   
   

5. Pull the 1/4" rubber hose off of the stock airbox. This may require some strength! Just be careful not to bust your hand when it finally comes off!
   
   
   

   
   
   

6. Unclip the air pump from the stock airbox.

    

    

   
   
   

7. Now you should be able to pull the stock airbox and intake tube out of the car by popping the box off of the grommets that hold it in place. 
   
   

    

   
   
   

8. Once the airbox and tube are out of the car, you can remove the stock snorkel. 
   
   

    

Coolant Hose Change

1. Locate the stock coolant line going from the radiator hose to a metal tube on the engine.

    

   
   
   

2. Pre-install the supplied squeeze clamps onto the COBB Hose a little ways up from the ends on the new line using a pair of pliers.
   
   

3. We recommend removing the line from the engine side first, as this allows a bit more room to catch the spills from the hose and metal tube.  Remove the clamp with pliers and pull the hose off the line.

    

   
   
   

4. Replace that end with the COBB hose. This way you can quickly swap the other end.
   
   

   
   
   

5. Once that's done you can move to the other end and remove the clamp.  Gently spin the line to break the rubber free from the plastic nipple on the radiator hose, be careful as the connection is plastic and may be brittle if the vehicle is older.  Once done you can pull off that end of the line and do your best to minimize spills while quickly installing the new line onto the radiator hose.  Any Indiana jones references you make while doing so earn double points.

    

   
   
   

6. You should now be free to install the other end and secure with the provided spring clamp.
   
   

   
   
   

7. Making sure to keep it away from the blades, use the zip tie to attach the new line to the fan shroud.  There is a small hole in some models that make this a little easier, make sure to cut off the excess.

    

   
   
   

8. You can now re-install the intake. Afterward refill your coolant level if necessary. (you may want to check your coolant level after you drive the car for the first time and allow it to cool down)

CARB Sticker Application

(Where Applicable)

1. Apply the supplied CARB sticker in a clear, easy to find location.  Typically underhood, or on the radiator core support.