Open

7G4600 - Redline Carbon Fiber Air Scoop F-150 / Raptor

2017 - 2022 Ford F150

Congratulations on your purchase of the COBB Tuning Redline Carbon Fiber Air Scoop! The following instructions will assist you through the installation process. Please read them BEFORE beginning the install to familiarize yourself with the steps and tools needed. If you feel you cannot properly perform this installation, we HIGHLY recommend you take the vehicle to a qualified and experienced automotive technician.

Stock Component Removal and Intake Brace Installation

Stock Intake Scoop Removal

1. Park your car in a safe area that is flat and level.
   
   
   

2. Remove the two trim clips holding the snorkel in place on the core support. Pull the center part of the clips out with your trim tool until they click and then pull out the lower part.
   
   

   Open

   

    

   Open

   

   
   
   

3. Remove the other trim clips that hold the plastic cover over the upper grill area. That cover can then be removed.
   
   

   Open

   

    

   Open

   

   
   
   

4. Grab your 8mm socket or wrench and remove the small bolt holding the intake scoop to the intake, then the snorkel can be removed from the engine bay.
   
   

   Open

   

    

COBB Intake Brace Installation

1. The bracket has double sided tape where it will stick to the core support, so first off try and clean a little off underneath it using a wet paper towel or an alcohol wipe if you have them. Let it dry.
   
   

   Open

   

   
   
   

2. Peel the backing off of the double-sided tape, then carefully slip the bracket in. You may have to gently flex (but not bend) the bracket to get it around the center of the ac condenser.
   
   

   Open

   

    

   Open

   

    

    

3. Line the threaded portion of the bracket up with the holes in the core support then push upwards to stick the bracket in place.
   
   

   Open

   

    

   Open

   

   
   
   

4. The threads should now line up with the two holes in the core support, with the tabs on the back holding it onto the core support.
   
   

   Open

   

    

5. You can now reinstall the cover but leave the trim clips off for now so you can get things lined up.

Carbon Scoop Installation

1. Slide the carbon scoop into place, wiggling left and right until the scoop clips into the airbox.
   
   
   

   Open

   

   
   
   

   Open

   

   
   
   

2. Using the plastic washers and Allen bolts, line up the holes in the scoop with the radiator support and loosely bolt them into place with the support bracket.
   
   
   

   Open

   

   
   
   

   Open

   

   
   
   

3. Slip the provided metal bushing into the rubber grommet.
   
   

   Open

   

   
   
   

4. Pop that assembly with the flat side of the grommet facing outwards into the scoop, then bolt it to the airbox using the stock screw through the grommet.
   
   

   Open

   

   
   
   

5. Install the stock 8mm headed screw with the remaining plastic washer to snug the scoop into the airbox.
   
   
   

   Open

   

   
   
   

6. Reinstall the trim clips into the radiator shroud as well as the 4 x 10mm bolts.
   
   

7. You can go ahead and snug up the allen bolts for the scoop using an m4 allen wrench.
   
   
   

   Open

   

   
   
   

8. You’re all done! Go out and enjoy!
   
   
   

CARB Sticker Application

D-660-129

(Where Applicable)

1. Apply the supplied CARB sticker in a clear, easy to find location.  Typically underhood, or on the radiator core support.

Links

MAP Notes

Helps to figure out which map you should be on given the parts installed to your car 

Links for related parts

Open