Versions Compared

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.

Image Removed

Table of Contents

How To: Datalog
Table of Contents
minLevel1
maxLevel6
outlinefalse
styledefault
typeflat
printabletrue

Accessport V3

Steps to Use:

  1. With the Accessport installed navigate to the "gauges" menu.

    shapes-1718813664142.pngImage Added


  2. If it's the first time you've gone to the gauge menu of the Accessport it will prompt you to ask how many monitors you want to display.  The selection can be updated later in the Gauge Setup menu.

  3. From the main gauge display, you can simply hit the center button on the Accessport in order to start logging.  (if logging manually, if autologging is enabled it will automatically start at this point). If you haven't pre-selected anything there are default parameters that will be logged which are typically the ones COBB Customer Support will ask you for.  Note that the Accessport will show

"logging"
  1. Logging at the top of the screen and at the bottom will let you know the logging rate.

  
  1. autolog specifics.pngImage Added


  2. In order to stop logging, you'll need to hit the center button on the Accessport again. Notice it now tells you it’s not logging.

    shapes-1718813703938.pngImage Added



Available Adjustments and How to Make Them:

Activating Autologging

  1. From the main menu of the Accessport select Gauges

    shapes-1718813664142.pngImage Added


  2. Navigate up to the Setup option, then Configure Datalogging. This will bring up the list of selectable datalogging parameters.

    shapes-1718813652767.pngImage Added

    shapes-1718813650158.pngImage Added


  3. It’ll pull up the list of datalogging parameters. Scroll up once again to the setup menu for this page, and go to Configure Logging Mode

    shapes-1718813648523.pngImage Added

    screenshot5.pngImage Added


  4. From here you can adjust between three modes.

    screenshot6.pngImage Added

    1. Manual Mode - You’ll need to press the center Accessport button when on the main gauges screen in order to start logging. Then press it again to stop.

    2. Automatic - Whenever the Accessport is on the gauges screen it will start to log. As the Accessport runs out of space to datalog it will begin to delete older logs to avoid filling up the system.

    3. Trigger Mode - Whenever certain conditions are met, the Accessport will start a datalog. The amount of time the log runs for and the conditions to trigger a log are customizable.

  5. Once selected you should see different messages on the main gauges screen depending on if you are in automatic, manual, or trigger mode, and currently logging or not currently logging. At any time you can stop an automatic log by pressing the center button.

shapes-1718813670881.pngImage Added

shapes-1718813672351.pngImage Added

Screenshot 2024-08-22 155438.pngImage Added


Trigger Logging Adjustments and How to Make Them:

Expand
titleClick to Expand

How to Add New Datalog Conditions:

  1. From the same menu where you can choose your logging mode, select Configure Datalog Triggers.

    image-20241030-194622.pngImage Added

  2. From here, select Add Trigger Condition.

    image-20241030-194659.pngImage Added

  3. From here, a list of available monitors that can be configured for Trigger Logging.

    screenshot10.pngImage Added

  4. After selecting the monitor you want to set up, you can then set Trigger Logging to activate when the chosen monitor is greater than, less than, or equal to a specific value.

    screenshot11.pngImage Addedscreenshot12.pngImage Added

  5. After setting the condition operator, the condition value can be adjusted.

    screenshot13.pngImage Added

How to View and Modify Trigger Conditions:

  1. From the Configure Datalog Conditions menu, select View/Modify Conditions.

    image-20241030-194754.pngImage Added

  2. This will display a list of current trigger conditions.

    screenshot5.pngImage Added

  3. After selecting a trigger condition to modify, adjustments can be made to the condition operator and condition value.

    image-20241030-195059.pngImage Added

How to Change Trigger Logging Timers:

  1. From the Configure Datalog Conditions menu, select Configure Condition Timers

    image-20241030-195539.pngImage Added

  2. From here, there are two different timers that can be adjusted: Lead-in time and Trailing time. These are how much time the log records before and after the trigger condition is met.

    image-20241030-195857.pngImage Addedimage-20241030-195914.pngImage Added

  3. Both options can be adjusted from 2 seconds to 10 seconds.

    image-20241030-195942.pngImage Added

How to Remove and Clear Trigger Conditions:

Remove Conditions:
  1. From the Configure Datalog Conditions menu, select Remove Condition.

    image-20241030-200046.pngImage Added

  2. This will display a list of current trigger conditions.

    screenshot2.pngImage Added

  3. Select a trigger condition to be removed from the list. You will see a confirmation message after the trigger condition has been removed.

    screenshot6.pngImage Added
Clear Trigger Conditions:
  1. From the Configure Datalog Conditions menu, select Clear Current Conditions.

    screenshot1.pngImage Added

  2. A confirmation message will appear after all conditions have been removed. After returning to the Configure Datalog Conditions menu, all options will be grayed out except Add Trigger Condition and Configure Trigger Timers.

    screenshot3.pngImage Addedimage-20241030-200126.pngImage Added


How to change Datalogging Monitors

Insert excerpt
How to Change Datalog Monitors
How to Change Datalog Monitors
nopaneltrue


How to Change Datalog Monitors -

 explains

 explains how to go through the process in order to change datalog monitors.

How to transfer maps and datalogs using Accessport Manager -

 covers

 covers migrating maps and datalogs to your computer

How to Change/Reset Displayed Gauges -

 explains

 explains the process for changing the displayed gauges.

Widget Connector
overlayyoutube
_templatecom/atlassian/confluence/extra/widgetconnector/templates/youtube.vm
width400px
urlhttps://www.youtube.com/watch?v=LlPnHnwAoEc
height300px






Accessport V2

Steps to Use:

Expand
titleSteps to Use:
  1. With the Accessport installed navigate to the "Monitor" menu.

    Image Modified

     

  2. From there select "Data Log" in order to capture engine data.

    Image Modified

  3. In order to stop logging, you'll need to hit the center button on the Accessport again.

    Image Modified
Available Adjustments and How to Make Them:

Customer Support

support@cobbtuning.com

Phone support available 9am to 6pm Monday-Thursday. 9am to 4pm Friday (CST)

866.922.3059

return to www.cobbtuning.com





Insert excerpt
PRS:Contact Us:
PRS:Contact Us:
nameContact Us:
nopaneltrue