Audi S3 (8V) 2015-2018


Supported Vehicles:

  • USDM 2015 - 2018 Audi S3

 


Map Revision:

Map

Version

Map

Version

Stage0
Stage1
Stage2

v303

Stage1+FlexFuel

v303

Required Accessport Firmware: 

  • AP3-VLK-003: 1.7.4.2-24849

Map Availability: 

  • Download from the Maps tab on the COBB Website

 

For more information on CARB Exemption Orders for this vehicle as well as the actual letter check out our page CARB EO numbers for COBB Audi Products


COBB Custom ECU Features:

These cars offer a variety of added features such as launch control and traction control. For more information check out our guide ​COBB Custom Features: Volkswagen MQB Platforms

 


 

Fuel Requirements:

Each map lists the minimum required octane. A higher octane fuel can be used safely on a map designed for lower octane. DO NOT use maps designed for higher octane with lower octane fuels. Top Tier gasoline should be used where available.

  • Maps designated with "91 OCT or 95 RON " are for use with 91 and 92 octane/95 RON fuel or better.

  • Maps designated with "93 OCT or 98 RON" are for use with 93 octane/98 RON fuel or better.

    • 94 octane with 0% Ethanol should run the ACN91 Map.

 

Running 0% Ethanol Fuels

These maps are designed for E10 fuel (fuel with 10% ethanol content). For those who only have access to E0 fuel (fuel with 0% ethanol) it is recommended to use the "91" and "ACN91" octane versions of the maps and datalog the car to ensure your fuel is performing to the necessary level. This is especially important for those using Canadian 94 octane E0 fuel. 

 

 



Stage1 Power Output

Stage 1

CARB EO: D-660-37

  • Intake Requirements : 

  • Exhaust Requirements: Stock exhaust or upgraded cat-back exhaust

  • Boost Target:

    • 91 Octane 95 RON Minimum: ~21 psi peak boost pressure tapering down to 16~ psi as you approach the 6800RPM redline, +/- ~1.5psi.

    • 93 Octane 98 RON Minimum: ~22 psi peak boost pressure tapering down to ~16psi as you approach the 6800RPM redline, +/- ~1.5psi.


Stage1+Flex Fuel

E## refers to the ethanol content (E) in % (##). So in the case of E10, it is 10% ethanol (Pump gas is typically between 7 & 15%)

Stage 1+Flex Fuel

Peak Power is achieved at 30% ethanol content

  • Intake Requirements : 

  • Exhaust Requirements: Stock exhaust or upgraded cat-back exhaust

  • Fueling Requirements: COBB Flex Fuel Upgrade Kit 3V2650

  • Boost Target:

    • 91 Octane 95 RON Minimum: ~21 psi peak boost pressure tapering down to 16~ psi as you approach the 6800RPM redline, +/- ~1.5psi.

    • 93 Octane 98 RON Minimum: ~22 psi peak boost pressure tapering down to ~16psi as you approach the 6800RPM redline, +/- ~1.5psi.

    • Ethanol: As much as an additional 2psi peak boost pressure with the most at 30% ethanol (E30)


Stage2 Power Output

Stage 2

CARB EO: D-660-39

  • Intake Requirements : 

  • Exhaust Requirements: Stock exhaust or upgraded cat-back exhaust

  • Intercooler: AMS Performance Front Mount Intercooler (CARB under D-825-3)

  • Drivetrain: Upgraded Clutch or DSG Software Recommended

  • Boost Target: 

    • 91 Octane 95 RON Minimum: ~24 psi peak boost pressure tapering down to ~19 psi as you approach the 6800RPM redline, +/- ~1.5psi.

    • 93 Octane 98 RON Minimum: ~25 psi peak boost pressure tapering down to ~21 psi as you approach the 6800RPM redline, +/- ~1.5psi.

 



Non-Performance Maps

Anti-Theft Mode

  • Will not allow vehicle to start

 

Valet

  • Fuel Requirements: 91 octane or better

  • Intake Requirements: Stock airbox and stock air filter

  • Exhaust Requirements: Stock exhaust

  • Boost Targets: Mechanical minimum

  • Rev Limiter: 3000RPM

*Not intended for aggressive driving*

 


 

Closing Warnings and Precautions:

  • Use of inappropriate calibration/modification combinations will promote engine damage.

  • Top Tier gasoline should be used where available. Use of lower quality fuels can result in catastrophic engine damage.

 


 

Revision Notes: 

 

Version

Notes

Version

Notes

v303

Updated to fix issue with ethanol monitor used monitor reading incorrectly

v302

Initial Flex Fuel Release

v301

Fixed error in CCF RPM Limiter

v300

 Updated for backend improvements.  Fixed bug where CCF adjustments sometimes didn't work via AP

v202

Maps updated to pick up fixes for factory impulse combustion

v201

No calibration changes.

This map has been updated to our Green Speed standard to ensure compliance with EPA and CARB regulations. This map eliminates unnecessary DTC suppression to ensure full environmental compliance.

 

 

Contact Us:

COBB Customer Support

Web Support and Tech Articles: COBB Tuning Customer Support Center

Email: support@cobbtuning.com

Phone support available 9am to 6pm Monday-Thursday. 9am to 4pm Friday (CST)

866.922.3059

 

return to www.cobbtuning.com

​

 

 

Copyright 2024 © COBB Tuning Products LLC. All Rights Reserved. | www.cobbtuning.com