v410

NexGen Stage2+Flex Fuel release

v401

Stage2+ NexGen release

v400

This map was updated to eliminate unnecessary DTC Supression or update versions for parity with other maps/vehicles within the platform

v361 

Adjusted fuel based protection system that operates at low DAM. No impact on normal operation.

v360

All VA WRX calibrations updated with new CCF2 ROM family and improvements noted in v350 (previously only for 2020 WRX), plus the following:

• Normal, LWG, and HWG calibration options for all stages

• Incorporated OEM Battery life improvements to applicable models (15-17)

v351

Improved high load driveability.

v350

Maps have been updated to eliminate unnecessary DTC suppression.

2020 WRX OTS utilized new CCF2 ROM family for improved driveability.  Some of the changes include:

• Improved closed-loop fueling and learning, improved airflow calculation and fuel targets.

• Improved charge temperature based boost target and control, and ignition compensation.

• Per gear timing and boost control, improved knock learning.

• "Soft" boost limit (via throttle), smoothed boost control input, reduced boost reduction at low air temperatures.

• Improved Anti-theft map (no start), improved Valet map (more restrictions i.e. 70 MPH speed limit)

• Additional groundwork to help Protuners 

v303

• 2018 ADM WRX: Fixed bug where the "Intake Temperature Pre-Turbo" monitor could sometimes show a value of -58F for a brief period of time after engine start. ECU did not use the erroneous value so this is a monitor issue only.

• Added 2019 ADM WRX support.

v302

2017 USDM WRX CVT/MT: Fixed an issue where real-time tuning and real-time map switching was disabled for the "MAF Calibration" table which caused the ECU to always use the reflashed values only for this table. 

• Note: Please REFLASH a v302 map to address this.

v301

• Fixed bugs associated with v300 maps preventing real-time and launch control feature changes from working.

• Addressed issue causing check engine light from being thrown for Stage2 maps

v300

Supports the latest Subaru ECU revision. Merged Subaru calibration for the latest injector timing changes.

v201

• Fixed bug causing Realtime map switching to not work.

• Added 2016 USDM WRX 6MT support.

• Added COBB BigSF Intake support.

v200

• Realtime tuning/map change feature added to v200 and later OTS maps (also requires latest Accessport firmware update to expose real-time map change function).

• Launch control (AP and cruise control adjustable) feature added to v200 and later OTS maps (also requires latest Accessport firmware update to expose launch RPM adjustment menu).

• Flat foot shifting (AP adjustable) feature added to v200 and later OTS maps (also requires the latest Accessport firmware update to expose flat-foot shift RPM adjustment menu).

• Merged Subaru calibration update for injector timing and other changes.

• Includes Subaru pre-ignition updates.

v115

• Renamed Stage1+TBE maps to Stage2

• Revised IAT vs. WGDC compensation to reduce underboosting between 32 F / 0 C and -40 F / -40 C

• Disabled Global A/F Learning #1 adjustment

• Slight revision to reduce DAM adjustment sensitivity at low loads

• Corrected issue with OL Enrichment vs. DAM fueling adjustment table

v114

Addresses an infrequent brief interruption of torque/power delivery introduced in the v113 maps.

v113

• Adds support for newest factory ECU/ROM update

• Reduced "rev hang" behavior when changing gears

• Optimized higher load ignition timing

• Revised how IAT vs. Ignition Timing compensations are applied at low load and RPM

• Changed long-term fuel trim behaviors at higher load values

• Improved AVCS and Requested Torque settings to improve power past 6000 RPM

• Revised Boost Target and WGDC vs. Baro. Comps to increase boost at high elevations

• Altered Per-Gear Ignition Timing compensations for 4/5/6th gears at high RPM for better resistance to detonation

• Slightly richer target AFR at high load and RPM

v109

• Revised low load/RPM timing to reduce knock corrections

• Smoothed Boost vs. IAT compensations for more predictable boost targeting

• Reduced Boost Target at higher RPM to raise knock threshold

• Adjusted Boost Target and WGDC Compensations for high elevations to address underboosting

• Added "High Waste Gate" secondary option mapping for cars experiencing persistent underboosting conditions

• Revised throttle mapping to increase sensitivity at partial accelerator pedal positions based on feedback from Airboy and others

• Richer target AFR at high load for increased detonation resistance

v105

• Revised ignition timing, primary fueling, camshaft timing, closed / open loop transition thresholds and boost levels for performance and safety.

• Optimized throttle mapping for improved take-off and more linear response across accelerator pedal range.

• Factory fueling and timing strategies streamlined for ease-of-calibration and consistency following a key-off and restart sequence.

• Per-Gear Timing Compensations revised for safety and enabled for 6th gear (OEM logic only allows for compensating gears 1-5).

v100

Initial Release

v401

Stage+ NexGen release

v400

This map was updated to eliminate unnecessary DTC Supression or update versions for parity with other maps/vehicles within the platform

v361

Adjusted fuel based protection system that operates at low DAM. No impact on normal operation.

v360

Updated all CVT WRX vehicles to CCF2 ROM Family maps.  Among those changes.

• Improved closed-loop fueling and learning

• IAT boost target compensation.

v350

• 2020 USDM WRX CVT initial support release

• Utilized new CCF2 ROM family for improved driveability.  Among those changes.

  • Improved closed-loop fueling and learning

  • IAT boost target compensation.

v302

2017 USDM WRX CVT/MT: Fixed an issue where real-time tuning and real-time map switching was disabled for the "MAF Calibration" table which caused the ECU to always use the reflashed values only for this table. 

• Note: Please REFLASH a v302 map to address this.

v301

Fixed bugs associated with v300 maps preventing real-time and launch control feature changes from working.

v300

Supports latest Subaru ECU revision.

v201

• Fixed bug causing Realtime map switching to not work.

• Added 2016 USDM WRX CVT support.

• Added COBB BigSF Intake support.

v200

• Realtime tuning now available.

• Merged Subaru calibration update for injector timing and other changes.

v117

Corrected issue where Launch Mode was not able to be activated on certain Stage1 v116 maps.

v116

• Original mapping for 2015 WRX CVT. 

• Revised ignition timing, primary fueling, camshaft timing, closed / open loop transition thresholds and boost levels for performance and safety.

• Factory fueling and timing strategies streamlined for ease-of-calibration and consistency following a key-off and restart sequence.

• Set speed limiters to maximum allowed value

• Per-Gear Timing Compensations revised for safety and enabled for 6^th - 8th gear in S# Mode (OEM logic only allows for compensating gears 1-5). 

• Launch Mode feature added to all performance maps.

• Includes Subaru pre-ignition update changes.