| DTC | Name of DTC | Meaning | Troubleshooting/ Description for AP |
|---|
| E1000 | COBB Internal DTC Data Error | problem with internal DTC system | Call support |
| E1010 | Analog Fuel Pressure Low Input | Voltage from sensor is lower than calibratable minimum, also a warning, engages fuel pressure safety, turns off differential fuel pressure comp. | Voltage from fuel pressure sensor is under the calibratable minimum. Check sensor for correct operation and compatibility with gateway |
| E1011 | Analog Fuel Pressure High Input | Voltage from sensor is higher than calibratable minimum, also a warning, engages fuel pressure safety, turns off differential fuel pressure comp. | Voltage from fuel pressure sensor is over the calibratable maximum. Check sensor for correct operation and compatibility with gateway |
| E10E0 | COBB Internal CTC AFM Configuration Error | RE | Call support |
| E10E1 | COBB Internal CTC RXHJ Configuration Error | RE | Call support |
| E10E2 | COBB Internal CTC TXHJ Configuration Error | RE | Call support |
| E10F0 | COBB Gateway Incorrect FW Version | Gateway FW is out of date or newer than requested by the map | Incorrect gateway fw version for map, bring gateway or map up to date |
| E10F1 | COBB Gateway Intermittent Activity | Not connected at startup, connected, then disconnected again. | Connection issue with gw, check cables |
| E10F2 | COBB CAN Gateway Inconsistent Sensor ID | Issue with the resistor in the harness or the sensor itself | Potential issue with cable, contact customer support |
| E10F3 | COBB CAN Gateway Module Temp Out of Range | gateway temperature is out of range for sensor | Gateway module temperature is out of the expected range, contact Cobb support. |
| E10F4 | COBB CAN Gateway Module High Temperature | gateway module is too hot. | Gateway module is too hot - allow to cool down and/ or re-locate the Gateway to avoid internal failure |
| E10F5 | COBB CAN Gateway Excessive Boot Time | Gateway took too long to start up | Gateway took too long to boot. If everything works fine after 30 seconds, this board may have skipped the QA test, and should be returned to Cobb |
| E10F6 | COBB CAN Gateway Data Requested Module Inactive | Map is setup for the gateway but the gateway is not responding or is inactive | Gateway not responding or inactive, check connections and fuses. If everything works fine after 30 seconds, this board may have skipped the QA test, and should be returned to Cobb |
| E1100 | Ethanol Sensor Configured But Not Detected | ECS is configured in the gateway but the harness and sensor are not detected | Ethanol content sensor and harness not detected, check all connection points. |
| E1101 | ECS Fuel Error | Code provided from the ethanol sensor, should drop WGDC to zero. | Ethanol Sensor Fuel Type Error. Fuel may be contaminated, or the sensor may be clogged or damaged. |
| E1102 | ECS Sensor Error | Code provided from the ethanol sensor, should drop WGDC to zero. | Ethanol sensor may be damaged, contact customer support. |
| E1103 | ECS Fuel or Sensor Error | Code provided from the ethanol sensor, should drop WGDC to zero. | Ethanol sensor fuel type error. Fuel may be contaminated, or the sensor may be clogged or damaged. |
| E1104 | ECS sensor data out of range | Code provided from the ethanol sensor, should drop WGDC to zero. | Ethanol sensor fuel type error. Fuel may be contaminated, or the sensor may be clogged or damaged. |
| E1105 | Ethanol Sensor Unplugged | ECS configured and the harness is present but the sensor is likely unplugged. | Ethanol content sensor harness detected but no sensor found, check connection to sensor |
| E1106 | ECS Fuel Temp Sensor configured but not detected | ECS is configured in the gateway but the harness and sensor are not detected | Ethanol content sensor and harness not detected, check all connection points. |
| E1107 | ECS Fuel Temp Sensor out of range | Fuel temperature is out of range for sensor | Fuel temperature is out of the expected range - contact Cobb support and check for other Gateway DTC's. |
| E1108 | ECS Fuel Temp Sensor Unplugged | ECS configured and the harness is present but the sensor is likely unplugged. | Ethanol content sensor harness detected but no sensor found, check connection to sensor |
| E1109 | Fuel Pressure Sensor Configured But Not Detected | Fuel pressure sensor is configured in the gateway but the harness and sensor are not detected | Fuel pressure sensor and harness not detected, check all connection points. |
| E110A | Fuel Pressure Sensor High Input V | input voltage from fuel pressure sensor is too high, may happen if using the incorrect sensor | Fuel pressure sensor input value too high, make sure you are using a gateway compatible sensor |
| E110B | Fuel Pressure Sensor Low Input V | input voltage from fuel pressure sensor is too low, may happen if using the incorrect sensor | Fuel pressure sensor input value too low, make sure you are using a gateway compatible sensor |
| E110C | Fuel Pressure Sensor Unplugged | Fuel pressure sensor configured and the harness is present but the sensor is likely unplugged. |
|