Part Number – Part Name

Vehicle Coverage

Congratulations on your purchase of the COBB Tuning xxxxxxxxxxxxx! The following instructions will assist you through the installation process. Please read them BEFORE beginning the install to familiarize yourself with the steps and tools needed. If you feel you cannot properly perform this installation, we HIGHLY recommend you take the vehicle to a qualified and experienced automotive technician.

IMPORTANT! Installing this kit will require custom tuning or utilizing an appropriate Stage Power Package map if you have a matching mechanical configuration. Please consult with COBB or an authorized ProTuner in your area if you have any questions!

862010 – COBB Rear Wiper Delete

Focus ST 2013-2018

Image Added

Table of Contents

Parts List

• Wiper Delete Top
• Wiper Delete Backing
• O-ring seal
• M8 x 1.25 nylon nut
• (2) Push in Bumpers
• (3) 4" Zip Ties
• (3) 6" Zip Ties
• Set of 3 different sized Rubber Washers
  

Tools Needed

• Phillips head screwdriver
• Flathead screwdriver

• 3/8" ratchet

• 3/8" 7mm socket

• 3/8" 8mm socket 

• 3/8" 10mm socket

• 3/8" 11mm socket 

• 3/8" 12mm socket 

• 3/8" 13mm socket
  

• 3/8" 14mm socket
  

• 3/8" 16mm socket
• 3/8" 17mm socket
• 3/8" 18mm socket
• 3/8" 21mm socket

• 3/8" 10mm deep socket

• 3/8" 12mm deep socket 
  

• 3/8" 14mm deep socket

• 3/8" 17mm deep socket

• 3/8" 14mm swivel socket
  

• 3/8" T20 Torx Bit

• 3/8" T25 Torx Bit

• 3/8" T30 Torx Bit

• 3/8" T40 Torx Bit

• 3/8" T50 Torx Bit
• 3/8" E10 inverted Torx
• 3/8" E12 inverted Torx
• 3/8" E14 inverted Torx
• 3/8" E18 inverted Torx

• 3/8" 5mm Hex Key or Hex Socket

• 3/8" 12" extension

• 3/8" 6" extension
  

• 3/8" Socket Swivel

• 1/2" breaker bar*
• 1/2" 16" extension*
• 1/2" 14mm socket*
• 14mm offset wrench
• Oxygen Sensor Wrench
• 7mm Hex Driver
• M3 Allen Key
• M4 Allen Key
• 8mm Ratcheting combination wrench
• 10mm combination wrench
• 11mm combination wrench
• 12mm combination wrench
• 13mm combination wrench
• 14mm combination wrench
• 15mm combination wrench
• 16mm combination wrench
• 17mm combination wrench
• 18mm combination wrench
• 19mm combination wrench
• 21mm combination wrench
• Torque Wrench

• Deadblow Hammer

• Torque Wrench
• Trim removal tool

• Pick

• Needlenose pliers

• Channel Lock Pliers

• Hose cutter
• Drain pan

Section 1

Section 2

Section 3

Section 4

Section 5

Links

MAP Notes

Helps to figure out which map you should be on given the parts installed to your car 

Rear Wiper Removal

1. Pop off the wiper spindle cover.
   
   Image Added
   
   
   
2. Using a 12mm Ratchet, remove the nut holding the wiper assembly in place.
   Note: At this point it's a good idea to use a permanent marker to mark the spindle and wiper arm to allow for easier re-installation in the future.
   
   
3. Remove the wiper arm, sometimes on older vehicles a small puller can be a big help.
   Note: Be very careful that you don't break the windshield prying against the glass or letting the arm snap down quickly.  The one used in the picture is a Lisle Tool 54150 Battery Terminal/Wiper Arm puller
   
   Image Added
   
   
   
4. Flipping over to the inside remove the strings connecting the package tray to the rear hatch.
   
   Image Added
   
   
   
5. Next up, pull out the center section of the ball socket since it's actually a clip, then remove the lower half using your trim tool.
   
   Image Added    Image Added
   
   
   
6. Carefully remove the Center section of trim by working from the outside ends towards the inside and gently pulling outwards.
   
   Image Added
   
   
   
7. Remove the trim clips holding the side panels on by popping out the center of the rivet first and then removing the base
   
   Image Added    Image Added
   
   
   
8. Now you can go ahead and remove the side panels
   
   Image Added
   
   
9. Go ahead and remove the handle in the bottom of the door trim by gently prying outward with your trim tool
   
   Image Added
   
   
   
10. With that out of the way the only things holding the main rear trim panel on to the hatch is the pop clips on each corner under where the side panels were.
    
    Image Added
    
    
    
11. Work around the sides slowly to pop the hidden clips holding the trim panel to the car and remove it from the car
    
    Image Added    Image Added
    
    
    
12. Unplug the harness from the wiper motor by gently depressing the tab
    
    Image Added
    
    
    
13. Using a 10mm socket remove the 3 bolts holding the wiper motor to the car and remove the entire assembly.
    
    
14. Using your fingers carefully remove the grommet from the glass.
    
    Image Added

Installing the COBB Rear Wiper Delete

1. Using a 13mm socket run the plastic nut down the threads on the delete and then remove, this is to loosen the threads a little bit to make getting it started by hand a little bit easier.
   
   Image Added
   
   
   
2. Clean the rear glass on the outside to improve the quality of the seal.
   
   
3. Install the o-ring into the wiper delete (a small amount of silicone lubricant on the o-ring can ensure a tighter seal later.
   
   Image Added
   
   
   
4. Install the small end of the rubber bumpers into the hold down bar.
   
   Image Added    Image Added
   
   
5. Next up you'll slide the appropriate rubber washer on to the threads.  This helps eat up the space between the delete and the glass and makes it easier to keep centered.  For the Mazdaspeed you'll use the largest one.
   
   Image Added
   
   
   
6. Holding the delete in place with one hand, get the bar on the back with the flat side of the bumpers towards the glass, and start slowly tightening the nut.
   
   Image Added
   
   
   
7. Once it's close to tight, get the logo angled to your liking and tighten it down.  Tightening more can make it look more flush but be careful not to over-tighten or it can shatter the glass.
   
   Image Added
   
   
   
8. Once you're happy with the angle and it's tight, you can zip tie up the wiring so it doesn't rattle.
   
   
9. After trimming the excess off the zip tie you can reinstall the interior in the reverse order of removal.
   
   
10. You're all done!  Go out and enjoy!
    
    
    

Customer Support

support@cobbtuning.com

Phone support available 9am to 6pm Monday-Thursday. 9am to 4pm Friday (CST)

866.922.3059