Porsche Data Monitor Support

6/19/2018

Table of Contents

maxLevel	2

Vehicle Support:

AP3-POR-001

2007-2009 Porsche 911 (997.1) Turbo WM
2008-2009 Porsche 911 (997.1) GT2 WM

AP3-POR-002

2010-2012 Porsche 911 (997.2) Turbo WM
2010-2012 Porsche 911 (997.2) Turbo S WM

AP3-POR-003

2010-2012 Porsche 911 (997.2) GT3 WM
2010-2012 Porsche 911 (997.2) GT3 RS WM

AP3-POR-004

2001-2005 Porsche 911 (996) Turbo MT WM
2001-2005 Porsche 911 (996) Turbo AT WM
2002-2005 Porsche 911 (996) Turbo X50 MT WM
2002-2005 Porsche 911 (996) Turbo X50 AT WM
2001-2005 Porsche 911 (996) GT2 MT WM

AP3-POR-005

2007-2008 Porsche 911 (997.1) GT3 MT WM
2007-2008 Porsche 911 (997.1) GT3 RS MT WM

AP3-POR-006

2014-2016 Porsche 911 (991) Turbo PDK WM
2014-2016 Porsche 911 (991) Turbo S PDK WM

AP3-POR-007

2012-2016 Porsche Cayman Boxster (981) MT WM
2012-2016 Porsche Cayman Boxster (981) PDK WM
2012-2016 Porsche Cayman (981) MT WM
2012-2016 Porsche Cayman (981) PDK WM
2012-2016 Porsche Cayman Boxster S (981) MT WM
2012-2016 Porsche Cayman Boxster S (981) PDK WM
2012-2016 Porsche Cayman S (981) MT WM
2012-2016 Porsche Cayman S (981) PDK WM
2014-2016 Porsche Cayman Boxster GTS (981) MT WM
2014-2016 Porsche Cayman Boxster GTS (981) PDK WM
2014-2016 Porsche Cayman GTS (981) MT WM
2014-2016 Porsche Cayman GTS (981) PDK WM
2015-2016 Porsche Cayman GT4 (981) MT WM
2016 Porsche Cayman GT4 Clubsport (981) PDK WM
2016 Porsche Boxster Spyder (981) MT WM

2012-2016 Porsche Carrera (991.1) MT WM
2012-2016 Porsche Carrera (991.1) PDK WM
2012-2016 Porsche Carrera (991.1) S MT WM
2012-2016 Porsche Carrera (991.1) S PDK WM
2012-2016 Porsche Carrera (991.1) S X51 MT WM
2012-2016 Porsche Carrera (991.1) S X51 PDK WM
2013-2016 Porsche Carrera (991.1) 4 MT WM
2013-2016 Porsche Carrera (991.1) 4 PDK WM
2013-2016 Porsche Carrera (991.1) 4S MT WM
2013-2016 Porsche Carrera (991.1) 4S PDK WM
2013-2016 Porsche Carrera (991.1) 4S X51 MT WM
2013-2016 Porsche Carrera (991.1) 4S X51 PDK WM
2015-2016 Porsche Carrera (991.1) GTS MT WM
2015-2016 Porsche Carrera (991.1) GTS PDK WM
2015-2016 Porsche Carrera (991.1) 4GTS MT WM
2015-2016 Porsche Carrera (991.1) 4GTS PDK WM

AP3-POR-008

2009-2012 Porsche Boxster S (987.2) MT WM
2009-2012 Porsche Boxster S (987.2) PDK WM
2009-2012 Porsche Cayman S (987.2) MT WM
2009-2012 Porsche Cayman S (987.2) PDK WM
2011-2012 Porsche Cayman R (987.2) MT WM
2011-2012 Porsche Cayman R (987.2) PDK WM
2011-2012 Porsche Boxster Spyder (987.2) MT WM
2011-2012 Porsche Boxster Spyder (987.2) PDK WM

2009-2012 Porsche Carrera S (997.2) MT WM
2009-2012 Porsche Carrera S (997.2) PDK WM
2009-2012 Porsche Carrera 4S (997.2) MT WM
2009-2012 Porsche Carrera 4S (997.2) PDK WM
2011-2012 Porsche Carrera GTS (997.2) MT WM
2011-2012 Porsche Carrera GTS (997.2) PDK WM
2011-2012 Porsche Carrera 4GTS (997.2) MT WM
2011-2012 Porsche Carrera 4GTS (997.2) PDK WM

AP3-POR-009

2017 Porsche Macan Base (95B) PDK USDM
2014-2017 Porsche Macan S (95B) PDK WM
2017 Porsche Macan GTS (95B) PDK WM
2014-2017 Porsche Macan Turbo (95B) PDK WM

AP3-POR-010 | AP3-POR-011 | AP3-POR-

PDK

012

20122017-2016 2021 Porsche Boxster Cayman Boxster (981718) PDK MT WM2012
2017-2016 2021 Porsche Boxster Cayman (981718) PDK WM2012
2017-2016 2021 Porsche Boxster Cayman Boxster S (981718) PDK MT WM2012
2017-2016 2021 Porsche Boxster Cayman S (981718) PDK WM2014
2018-2016 2019 Porsche Boxster Cayman Boxster GTS (981718) PDK WM2014
2018-2016 2019 Porsche Boxster Cayman GTS (981718) PDK WM2016
2020-2021 Porsche Boxster Cayman GT4 Clubsport T (981718) PDK WM
20142020-2016 Porsche 911 Turbo (9912021 Porsche Boxster Cayman T (718) PDK WM WM2014

2017-2016 2019 Porsche 911 Turbo S Carrera (991.2) MT WM
2017-2019 Porsche 911 Carrera (991.2) PDK WM2012
2017-2016 2019 Porsche 911 Carrera Cabriolet (991.2) PDK MT WM2012
2017-2016 2019 Porsche Carrera 911 Carrera Cabriolet (991.2) S PDK WM2012
2017-2016 2019 Porsche 911 Carrera 4 (991.2) S X51 PDK MT WM2013
2017-2016 2019 Porsche 911 Carrera 4 (991.2) 4 PDK WM2013
2017-2016 2019 Porsche 911 Carrera 4 Cabriolet (991.2) 4S PDK MT WM2013
2017-2016 2019 Porsche 911 Carrera 4 Cabriolet (991.2) 4S X51 PDK WM2015
2017-2016 2019 Porsche 911 Carrera S (991.2) GTS PDK MT WM2015
2017-2016 2019 Porsche 911 Carrera S (991.2) 4GTS PDK WM

AP3-POR-001/004: (997.1/996 Turbo/GT2) Data Monitors

**Bolded items indicate an automatically set Accessport default data log parameter

Actual Camshaft Angle Bank 1-Actual camshaft angle for Bank 1.

Actual Camshaft Angle Bank 2-Actual camshaft angle for Bank 2.

Actual Gear-Current transmission position.

Ambient Pressure-Barometric Pressure

Ambient Temperature-Ambient air temperature.

Battery Voltage-Battery Voltage

Boost Error- Calculated boost error.

Catalytic Converter Temperature (Modeled)-Temperature of catalytic converter. This is a modeled temperature so not 100% accurate.

Cold Start Enrichment Range 0-No Description

Cold Start Enrichment Range 1-No Description

Cold Start Enrichment Range 2-No Description

Coordinated Torque for Cylinder Filling-No Description

Current Starting Adaptation Factor-Amount of correction in percentage of correction when starting the car.

Distance Since Power Failure-Distance amount since a power failure.

Distance With Check Engine On-Distance with a check engine light on.

EGT Downstream of Cat (Modeled)-Exhaust gas temperature behind the catalytic converter. This is a modeled temperature so not 100% accurate.

EGT Upstream of Cat (Modeled)-Exhaust gas temperature before the catalytic converter. This is a modeled temperature so not 100% accurate.

Engine Compartment Temperature- Engine compartment temperature. Measured in the back of the car.

Engine Oil Temperature- Temperature of engine oil.

Engine RPM- Engine Speed

Engine Temperature- Engine coolant temp.

Engine Torque Loss-No Description

Fuel Level-Fuel level.

Ignition Angle (Actual)-Final ignition timing value after all corrections.

Injection Time- Injector open time in milliseconds.

Intake-Air Temperature-Intake air temperature in the intake manifold.

Knock Sums Cyl. 1- Knock Sums for cylinder number 1

Knock Sums Cyl. 2- Knock Sums for cylinder number 2

Knock Sums Cyl. 3- Knock Sums for cylinder number 3

Knock Sums Cyl. 4- Knock Sums for cylinder number 4

Knock Sums Cyl. 5- Knock Sums for cylinder number 5

Knock Sums Cyl. 6- Knock Sums for cylinder number 6

Lambda Bank 1-Air fuel reading from the wideband sensors Bank 1

Lambda Bank 2- Air fuel reading from the wideband sensors Bank 2

Load (Relative) – Relative Load.

Load rlp- Load

Long Term Fuel Trim Bank 1-Long term fuel trim for Bank 1.

Long Term Fuel Trim Bank 2-Long term fuel trim for Bank 2.

MAF 2-Mass air flow reading Bank 2

MAF-Mass Airflow Reading Bank 1.

Manifold Absolute Pressure-Manifold pressure. This is an inferred boost calculation.

Maximum Torque-Maximum torque value

Minimum Torque-Minimum Torque Value

Nominal Throttle Plate Angle-Actual Throttle Angle

Operating Time Since Power Failure-Amount of time since power failure.

Pre Throttle Pressure Sensor-Pressure throttle pressure sensor. (997.1 only) This monitor can be used for "Boost" pressure.

Radiator Fan Request Value-Radiator fan on and off request.

Relative Secondary Air Mass Bank 1-No Description

Relative Secondary Air Mass Bank 2- No Description

Set Point Torque- Set point torque value.

Short Term Fuel Trim Bank 1-Short term fuel trim for Bank 1.

Short Term Fuel Trim Bank 2-Short term fuel trim for Bank 2.

Target Boost Pressure- Boost pressure set point.

Turbo Duty Cycle Bank 1 (Target)- WGDC/VTG target duty cycle from 0-100%

Turbo Duty Cycle Bank 2 (Target)- WGDC/VTG target duty cycle from 0-100%

Turbo Duty Cycle Bank 1 (Actual)- WGDC/VTG actual duty cycle from 0-100%

Turbo Duty Cycle Bank 2 (Actual)- WGDC/VTG actual duty cycle from 0-100%

Target Camshaft Angle Bank 1-Target camshaft position for Bank 1.

Target Camshaft Angle Bank 2-Target camshaft position for Bank 2.

Target Firing Angle of Torque Intervention-No Description.

Target Idle Speed- Idle speed target.

Throttle Angle-Desired Throttle Angle

Total Mass Air Flow (MAF+Tank Vent)-This is a combination of MAF plus the tank vent recirc total airflow.

Vehicle Speed-Vehicle Speed

Warm-up Cycle Counter-Cycle counter for the warm up cycle.

AP3-POR-002: (997.2 Turbo/Turbo S) Data Monitors

**Bolded items indicate an automatically set Accessport default data log parameter

*Items are separated into blocks (G01, G0F, etc..). Limiting the number of blocks will increase sample

2017-2019 Porsche 911 Carrera S Cabriolet (991.2) MT WM
2017-2019 Porsche 911 Carrera S Cabriolet (991.2) PDK WM
2017-2019 Porsche 911 Carrera 4S (991.2) MT WM
2017-2019 Porsche 911 Carrera 4S (991.2) PDK WM
2017-2019 Porsche 911 Carrera 4S Cabriolet (991.2) MT WM
2017-2019 Porsche 911 Carrera 4S Cabriolet (991.2) PDK WM
2017-2019 Porsche 911 Carrera GTS (991.2) MT WM
2017-2019 Porsche 911 Carrera GTS (991.2) PDK WM
2017-2019 Porsche 911 Carrera GTS Cabriolet (991.2) MT WM
2017-2019 Porsche 911 Carrera GTS Cabriolet (991.2) PDK WM
2017-2019 Porsche 911 Carrera 4 GTS (991.2) MT WM
2017-2019 Porsche 911 Carrera 4 GTS (991.2) PDK WM
2017-2019 Porsche 911 Carrera 4 GTS Cabriolet (991.2) MT WM
2017-2019 Porsche 911 Carrera 4 GTS Cabriolet (991.2) PDK WM
2017-2019 Porsche 911 Targa 4 (991.2) MT WM
2017-2019 Porsche 911 Targa 4 (991.2) PDK WM
2017-2019 Porsche 911 Targa 4S (991.2) MT WM
2017-2019 Porsche 911 Targa 4S (991.2) PDK WM
2017-2019 Porsche 911 Targa 4 GTS (991.2) MT WM
2017-2019 Porsche 911 Targa 4 GTS (991.2) PDK WM
2018-2019 Porsche 911 Carrera T (991.2) MT WM
2018-2019 Porsche 911 Carrera T (991.2) PDK WM

2017-2019 Porsche 911 Turbo (991.2) PDK WM
2017-2019 Porsche 911 Turbo S (991.2) PDK WM
2018-2019 Porsche 911 Turbo S Exclusive Series (991.2) PDK WM
2018-2019 Porsche 911 GT2RS (991.2) PDK WM

AP3-POR-PDK

2012-2016 Porsche Cayman Boxster (981) PDK WM
2012-2016 Porsche Cayman (981) PDK WM
2012-2016 Porsche Cayman Boxster S (981) PDK WM
2012-2016 Porsche Cayman S (981) PDK WM
2014-2016 Porsche Cayman Boxster GTS (981) PDK WM
2014-2016 Porsche Cayman GTS (981) PDK WM
2016 Porsche Cayman GT4 Clubsport (981) PDK WM
2014-2016 Porsche 911 Turbo (991) PDK WM
2014-2016 Porsche 911 Turbo S (991) PDK WM
2012-2016 Porsche Carrera (991) PDK WM
2012-2016 Porsche Carrera (991) S PDK WM
2012-2016 Porsche Carrera (991) S X51 PDK WM
2013-2016 Porsche Carrera (991) 4 PDK WM
2013-2016 Porsche Carrera (991) 4S PDK WM
2013-2016 Porsche Carrera (991) 4S X51 PDK WM
2015-2016 Porsche Carrera (991) GTS PDK WM
2015-2016 Porsche Carrera (991) 4GTS PDK WM

AP3-POR-001/004: (997.1/996 Turbo/GT2) Data Monitors

**Bolded items indicate an automatically set Accessport default data log parameter

Actual Camshaft Angle Bank 1-Actual camshaft angle for Bank 1.
Actual Camshaft Angle Bank 2-Actual camshaft angle for Bank 2.
Actual Gear-Current transmission position.
Ambient Pressure-Barometric Pressure
Ambient Temperature-Ambient air temperature.
Battery Voltage-Battery Voltage
Boost Error- Calculated boost error.
Catalytic Converter Temperature (Modeled)-Temperature of catalytic converter. This is a modeled temperature so not 100% accurate.
Cold Start Enrichment Range 0-No Description
Cold Start Enrichment Range 1-No Description
Cold Start Enrichment Range 2-No Description
Coordinated Torque for Cylinder Filling-No Description
Current Starting Adaptation Factor-Amount of correction in percentage of correction when starting the car.
Distance Since Power Failure-Distance amount since a power failure.
Distance With Check Engine On-Distance with a check engine light on.
EGT Downstream of Cat (Modeled)-Exhaust gas temperature behind the catalytic converter. This is a modeled temperature so not 100% accurate.
EGT Upstream of Cat (Modeled)-Exhaust gas temperature before the catalytic converter. This is a modeled temperature so not 100% accurate.
Engine Compartment Temperature- Engine compartment temperature. Measured in the back of the car.
Engine Oil Temperature- Temperature of engine oil.
Engine RPM- Engine Speed
Engine Temperature- Engine coolant temp.
Engine Torque Loss-No Description
Fuel Level-Fuel level.
Ignition Angle (Actual)-Final ignition timing value after all corrections.
Injection Time- Injector open time in milliseconds.
Intake-Air Temperature-Intake air temperature in the intake manifold.
Knock Sums Cyl. 1- Knock Sums for cylinder number 1
Knock Sums Cyl. 2- Knock Sums for cylinder number 2
Knock Sums Cyl. 3- Knock Sums for cylinder number 3
Knock Sums Cyl. 4- Knock Sums for cylinder number 4
Knock Sums Cyl. 5- Knock Sums for cylinder number 5
Knock Sums Cyl. 6- Knock Sums for cylinder number 6
Lambda Bank 1-Air fuel reading from the wideband sensors Bank 1
Lambda Bank 2- Air fuel reading from the wideband sensors Bank 2
Load (Relative) – Relative Load.
Load rlp- Load
Long Term Fuel Trim Bank 1-Long term fuel trim for Bank 1.
Long Term Fuel Trim Bank 2-Long term fuel trim for Bank 2.
MAF 2-Mass air flow reading Bank 2
MAF-Mass Airflow Reading Bank 1.
Manifold Absolute Pressure-Manifold pressure. This is an inferred boost calculation.
Maximum Torque-Maximum torque value
Minimum Torque-Minimum Torque Value
Nominal Throttle Plate Angle-Actual Throttle Angle
Operating Time Since Power Failure-Amount of time since power failure.
Pre Throttle Pressure Sensor-Pressure throttle pressure sensor. (997.1 only) This monitor can be used for "Boost" pressure.
Radiator Fan Request Value-Radiator fan on and off request.
Relative Secondary Air Mass Bank 1-No Description
Relative Secondary Air Mass Bank 2- No Description
Set Point Torque- Set point torque value.
Short Term Fuel Trim Bank 1-Short term fuel trim for Bank 1.
Short Term Fuel Trim Bank 2-Short term fuel trim for Bank 2.
Target Boost Pressure- Boost pressure set point.
Turbo Duty Cycle Bank 1 (Target)- WGDC/VTG target duty cycle from 0-100%
Turbo Duty Cycle Bank 2 (Target)- WGDC/VTG target duty cycle from 0-100%
Turbo Duty Cycle Bank 1 (Actual)- WGDC/VTG actual duty cycle from 0-100%
Turbo Duty Cycle Bank 2 (Actual)- WGDC/VTG actual duty cycle from 0-100%
Target Camshaft Angle Bank 1-Target camshaft position for Bank 1.
Target Camshaft Angle Bank 2-Target camshaft position for Bank 2.
Target Firing Angle of Torque Intervention-No Description.
Target Idle Speed- Idle speed target.
Throttle Angle-Desired Throttle Angle
Total Mass Air Flow (MAF+Tank Vent)-This is a combination of MAF plus the tank vent recirc total airflow.
Vehicle Speed-Vehicle Speed
Warm-up Cycle Counter-Cycle counter for the warm up cycle.

AP3-POR-002: (997.2 Turbo/Turbo S) Data Monitors

**Bolded items indicate an automatically set Accessport default data log parameter

*Items are separated into blocks (G01, G0F, etc..). Limiting the number of blocks will increase sample frequency. Whether one item in a block is queried or all of them the logging speed will not change so try and group as many items in as little blocks as possible. This is why you may notice duplicates of some monitors. EX. Choosing (G02) Engine Speed and (G02) Oil Pressure will log faster than selecting (G27) Engine Speed and (G02) Oil Pressure.

(G1) Ambient Pressure – This value is measured by the ambient pressure sensor in the DME control unit and is used to calculate the altitude correction factor. The altitude correction factor is used to inhibit secondary air, tank vent valve and fuel tank leakage diagnosis. If the mass air flow sensor (MAF) fails, a substitute value for the air mass is formed from the engine speed, throttle position and altitude correction factor. The measuring range is from 400 mbar to 1200 mbar.
(G1) Fuel Pressure - The fuel high-pressure value, measured by the fuel pressure sensor, is displayed here. The flow control valve at the fuel high-pressure pump regulates the fuel pressure from approx. 40,000 mbar at idle speed up to 120,000 mbar at full throttle. The diagnosis monitors the deviation between the required and actual value.
(G1) Measured Coolant Temp – The coolant temperature is calculated from the voltage signal of the engine temperature sensor and is used to correct the DME maps in accordance with the temperature. The temperature is passed on to the gateway control unit via CAN. It is also used as the basis for thermostat diagnosis. (The warm-up phase is monitored using a temperature model.) If there is no signal, a substitute value is formed in the DME control unit and is then displayed here.
(G2) Engine Speed - The actual value of the current engine speed is measured via the pulse sender on the flywheel (60 - 2 pulses per revolution).
(G2) Battery Voltage - Supply voltage at terminal 15 on the DME control unit. If a limit value is not reached, the idle speed of the engine can be increased in order to improve the load balance.
(G2) Vehicle Speed - Current vehicle speed. The vehicle speed comes from ABS/ASR/PSM via CAN. This is used as an input requirement for various diagnoses and as freeze frame content.
(G2) AT Flag - Flag that determines if the car has an auto transmission or not.
(G2) Oil Pressure - Absolute engine oil pressure incl. ambient pressure. Approx. 1,000 mbar (ambient pressure) must be subtracted for the relative engine oil pressure (overpressure). This then corresponds to the value displayed on the instrument cluster.
(G2) Pre Throttle Boost Pressure - Boost pressure before the throttle plate.
(G3) MAP- Manifold Absolute Pressure, also boost pressure after the throttle plate.
(G3) Target Map - Target boost pressure.
(G3) Ambient pressure - This value is measured by the ambient pressure sensor in the DME control unit and is used to calculate the altitude correction factor. The altitude correction factor is used to inhibit secondary air, tank vent valve and fuel tank leakage diagnosis. If the mass air flow sensor (MAF) fails, a substitute value for the air mass is formed from the engine speed, throttle position and altitude correction factor. The measuring range is from 400 mbar to 1200 mbar.
(G4) Target Throttle Plate Position - Requested throttle position.
(G4) Actual Throttle Plate Position - The actual throttle valve angle is the opening angle recorded by the throttle valve potentiometer (° throttle valve angle), approx. 0.00 ° (throttle valve fully closed) to 80.00 ° (at full throttle position).
(G7) Actual Fuel Pressure - The fuel high-pressure value, measured by the fuel pressure sensor, is displayed here. The flow control valve at the fuel high-pressure pump regulates the fuel pressure from approx. 40,000 mbar at idle speed up to 120,000 mbar at full throttle. The diagnosis monitors the deviation between the required and actual value.
(G7) Target Fuel Pressure - Target fuel pressure.
(GB) Intake Cam Timing B1- The actual camshaft angle is the position of the intake camshafts recorded by the hall senders. An actual value of approx. 125.00 °crk is displayed at idle speed. This value can change to approx. 85.00 °crk during acceleration at full throttle. This results in an adjustment value of approx. 0.00 °crk at idle speed and up to 40.00 °crk at full throttle.
(GB) Intake Cam Timing B2- The actual camshaft angle is the position of the intake camshafts recorded by the hall senders. An actual value of approx. 125.00 °crk is displayed at idle speed. This value can change to approx. 85.00 °crk during acceleration at full throttle. This results in an adjustment value of approx. 0.00 °crk at idle speed and up to 40.00 °crk at full throttle.
(GB) Intake Camshaft Phase B1- Measured cam phase bank 1.
(GB) Intake Camshaft Phase B2 - Measured cam phase bank 2.
(GF) Requested Fuel - Requested fuel consumption.
(GF) Target Fuel Mass - Target fuel mass.
(GF) Gear Shift Sync Speed Setpoint - Setpoint requested to sync the shiftspeed.
(GF) Air Fuel B1 - Actual lambda value bank 1
(GF) Air Fuel B2 - Actual lambda value bank 2
(GF) Air Fuel Adaption B1 - Long term fuel trim bank 1
(GF) Air Fuel Adaption B2 - Long term fuel trim bank 2
(G0F) Target Clutch Torque- Torque targeted at the clutch.
(G0F) Actual Clutch Torque- Actual torque value at the clutch
(G11) Short Term Fuel Trim B1 - Short term fuel trim bank 1 - These are backwards from traditional STFT. Meaning a value of +5.00 is removing 5% of fuel,and -5.00 is adding 5% fuel.
(G11) Short Term Fuel Trim B2 - Short term fuel trim bank 2 - These are backwards from traditional STFT. Meaning a value of +5.00 is removing 5% of fuel,and -5.00 is adding 5% fuel.
(G16) Adaptive Fuel Mass - Adapted fuel mass.
(G16) Target Pre Throttle Pressure – Target pre throttle boost pressure. This is your overall boost target.
(G17) Knock Retard Cyl 1 – Amount of timing being retarded Cylinder 1
(G17) Knock Retard Cyl 2 – Amount of timing being retarded Cylinder 2
(G17) Knock Retard Cyl 3 – Amount of timing being retarded Cylinder 3
(G17) Knock Retard Cyl 4 – Amount of timing being retarded Cylinder 4
(G17) Knock Retard Cyl 5 – Amount of timing being retarded Cylinder 5
(G17) Knock Retard Cyl 6 – Amount of timing being retarded Cylinder 6
(G17) Intake Cam Timing B1 - Amount of intake cam advance bank 1.
(G17) Intake Cam Timing B2 - Amount of intake cam advance bank 2.
(G18) Actual Ignition Angle - Actual ignition timing of the car.
(G18) Target Ignition Angle - Target ignition timing of the car.
(G18) Average Knock Retard - Averaged value of knock retard.
(G18) Average ADV1 Value - Average ADV1 Value.
(G18) Engine Speed - Engine Speed in RPM
(G18) MAP - Manifold Absolute Pressure, also boost pressure after the throttle plate.
(G18) Coolant Temp - Engine coolant temperature.
(G19) Target Air Fuel Ratio B1 - Target lambda value bank 1
(G19) Target Air Fuel Ratio B2 - Target lambda value bank 2
(G19) Actual Air Fuel Ratio B1 - Actual lambda value bank 1
(G19) Actual Air Fuel Ratio B2 - Actual lambda value bank 2
(G1C) Engine Speed - Engine Speed in RPM
(G1C) Relative engine load - Engine load used by the ECU.
(G1C) Coolant Temperature - Engine coolant temperature.
(G1D) Injection Time 1 Cyl 1 - Injection time for the fuel injection system Cyl 1
(G1D) Injection Time 1 Cyl 2 - Injection time for the fuel injection system Cyl 2
(G1D) Injection Time 1 Cyl 3 - Injection time for the fuel injection system Cyl 3
(G1D) Injection Time 1 Cyl 4 - Injection time for the fuel injection system Cyl 4
(G1D) Injection Time 1 Cyl 5 - Injection time for the fuel injection system Cyl 5
(G1D) Injection Time 1 Cyl 6 - Injection time for the fuel injection system Cyl 6
(G1E) Injection Time 2 Cyl 1 - Injection time 2 for the fuel injection system Cyl 1
(G1E) Injection Time 2 Cyl 2 - Injection time 2 for the fuel injection system Cyl 2
(G1E) Injection Time 2 Cyl 3 - Injection time 2 for the fuel injection system Cyl 3
(G1E) Injection Time 2 Cyl 4 - Injection time 2 for the fuel injection system Cyl 4
(G1E) Injection Time 2 Cyl 5 - Injection time 2 for the fuel injection system Cyl 5
(G1E) Injection Time 2 Cyl 6 - Injection time 2 for the fuel injection system Cyl 6
(G22) EGT at Lambda Sensor B1- Exhaust gas temperature measured at the lambda sensor bank 1
(G23) EGT at Lambda Sensor B2 - Exhaust gas temperature measured at the lambda sensor bank 1
(G27) Engine Speed - The actual value of the current engine speed is measured via the pulse sender on the flywheel (60 - 2 pulses per revolution).
(G27) Average Air Fuel B1 - Averaged lambda value bank 1
(G27) Average Air Fuel B2 - Averaged lambda value bank 2
(G2D) Pre Throttle Closed Loop Integral PID- Integral control for the PUT control.
(G2D) Pre Throttle Pressure Sensor Voltage- Voltage of the PUT sensor.
(G36) Target Air Fuel Ratio B1 - Target lambda value bank 1
(G36) Actual Air Fuel Ratio B1 - Target lambda value bank 2
(G36) Engine Speed - Engine Speed in RPM
(G36) Actual Fuel Pressure - Measured fuel pressure.
(G36) Target Fuel Pressure - Target fuel pressure.
(G36) Relative engine load - Engine load used by the ECU.
(G37) MAP - Manifold Absolute Pressure, also boost pressure after the throttle plate.
(G36) Target Air Fuel Ratio B1 - Target lambda value bank 1
(G36) Actual Air Fuel Ratio B2 - Target lambda value bank 2
(G37) Short Term Fuel Trim B1 - Short term fuel trim bank 1
(G37) Short Term Fuel Trim B2 - Short term fuel trim bank 2
(G37) Actual Throttle Plate Position - Actual throttle position.
(G40) Intake Air Temperature - Measured intake air temperature.
(G40) Oil Temperature - Oil Temperature.
(G43) Predicted Air Mass- Final calculated airflow value.
(G5C) Accelerator Pedal Position - Accelerator Pedal position.
(G5C) Exhaust Gas Temperatures B1 - Exhaust gas temperature bank 1
(G5C) Exhaust Gas Temperatures B2 - Exhaust gas temperature bank 2
(G5D) Actual turbine actuator B1 Actual duty cycle of the VTG controller 0-100% Bank 1
(G5D) Actual turbine actuator B2 Actual duty cycle of the VTG controller 0-100% Bank 2
(G5D) Target Turbine Actuator B1 Target duty cycle of the VTG controller 0-100% Bank 1
(G5D) Target Turbine Actuator B2 Target duty cycle of the VTG controller 0-100% Bank 2
(G63) Target Map - Target boost pressure.
(G63) MAP - Manifold Absolute Pressure, also boost pressure after the throttle plate.
(G63) Exhaust Gas Temperatures B1 - Exhaust gas temperature bank 1
(G63) Exhaust Gas Temperatures B2 - Exhaust gas temperature bank 2
(G63) Pre Throttle Boost Pressure - Boost pressure before the throttle plate.
(G63) Engine Speed - Engine Speed in RPM
(G63) Actual Ignition Angle - Actual ignition timing of the car.
(G6E) Fuel Pump #1 Switch - On/Off flag for fuel pump #1
(G6E) Fuel Pump #2 Switch - On/Off flag for fuel pump #2
(G75) Full Load Switch - Flag that determines if the car is at full load.
(G7D) Maximum Available Torque - Maximum available torque.
(G7D) Fast ASR Intervention Torque - Fast ASR Intervention Torque
(G7D) Actual Engine Torque - Measured Engine Toruqe
(G7D) Target Engine Torque - Target Engine Torque

AP3-POR-003/005: (997.1/997.2 GT3/GT3 RS) Data Monitors

**Bolded items indicate an automatically set Accessport default data log parameter

Actual Camshaft Angle Bank 1-Actual camshaft angle for Bank 1.
Actual Camshaft Angle Bank 2-Actual camshaft angle for Bank 2.
Actual Gear-Current transmission position.
Ambient Pressure-Barometric Pressure
Ambient Temperature-Ambient air temperature.
Battery Voltage-Battery Voltage
Catalytic Converter Temperature (Modeled)-Temperature of catalytic converter. This is a modeled temperature so not 100% accurate.
Cold Start Enrichment Range 0-No Description
Cold Start Enrichment Range 1-No Description
Cold Start Enrichment Range 2-No Description
Coordinated Torque for Cylinder Filling-No Description
Current Starting Adaptation Factor-Amount of correction in percentage of correction when starting the car.
Distance Since Power Failure-Distance amount since a power failure.
Distance With Check Engine On-Distance with a check engine light on.
Driving Cycle Counter-Driving cycle counter for readiness monitors.
EGT Downstream of Cat (Modeled)-Exhaust gas temperature behind the catalytic converter. This is a modeled temperature so not 100% accurate.
EGT Upstream of Cat (Modeled)-Exhaust gas temperature before the catalytic converter. This is a modeled temperature so not 100% accurate.
Engine Compartment Temperature- Engine compartment temperature. Measured in the back of the car.
Engine Oil Temperature- Temperature of engine oil.
Engine RPM- Engine Speed
Engine Temperature- Engine coolant temp.
Engine Torque Loss-No Description
Fuel Level-Fuel level.
Ignition Angle (Actual)-Final ignition timing value after all corrections.
Injection Time- Injector open time in milliseconds.
Intake-Air Temperature-Intake air temperature in the intake manifold.
Knock Sums Cyl. 1- Knock Sums for cylinder number 1
Knock Sums Cyl. 2- Knock Sums for cylinder number 2
Knock Sums Cyl. 3- Knock Sums for cylinder number 3
Knock Sums Cyl. 4- Knock Sums for cylinder number 4
Knock Sums Cyl. 5- Knock Sums for cylinder number 5
Knock Sums Cyl. 6- Knock Sums for cylinder number 6
Lambda Bank 1-Air fuel reading from the wideband sensors Bank 1
Lambda Bank 2- Air fuel reading from the wideband sensors Bank 2
Load (Relative) – Relative Load.
Load rlp- Load
Long Term Fuel Trim Bank 1-Long term fuel trim for Bank 1.
Long Term Fuel Trim Bank 2-Long term fuel trim for Bank 2.
MAF 2-Mass air flow reading Bank 2
MAF-Mass Airflow Reading Bank 1.
Manifold Absolute Pressure-Manifold pressure above atmospheric pressure, boost.
Maximum Torque-Maximum torque value
Minimum Torque-Minimum Torque Value
Nominal Throttle Plate Angle-Actual Throttle Angle
Operating Time Since Power Failure-Amount of time since power failure.
Radiator Fan Request Value-Radiator fan on and off request.
Relative Secondary Air Mass Bank 1-No Description
Relative Secondary Air Mass Bank 2- No Description
Set Point Torque- Set point torque value.
Short Term Fuel Trim Bank 1-Short term fuel trim for Bank 1.
Short Term Fuel Trim Bank 2-Short term fuel trim for Bank 2.
Target Camshaft Angle Bank 1-Target camshaft position for Bank 1.
Target Camshaft Angle Bank 2-Target camshaft position for Bank 2.
Target Firing Angle of Torque Intervention-No Description.
Target Idle Speed- Idle speed target.
Throttle Angle-Desired Throttle Angle
Total Mass Air Flow (MAF+Tank Vent)-This is a combination of MAF plus the tank vent recirc total airflow.
Vehicle Speed-Vehicle Speed
Warm-up Cycle Counter-Cycle counter for the warm up cycle.

AP3-POR-006: (991.1) Turbo / Turbo S Data Monitors

**Bolded items indicate an automatically set Accessport default data log parameter

Ambient Air Pressure- Ambient Air Pressure from ECU
Boost (Map Actual)- Manifold Absolute Pressure Actual Value
Boost (Map Target)- Manifold Absolute Pressure Target Value
Boost 1( Pre Throttle)- Boost pressure up throttle actual value
Boost 2(Pre Throttle)- Boost pressure up throttle target value
Diverter Valve- 0 or 1 meaning active (1) or not active (0).
Engine Load- Engine load value from 0-100%
Engine Oil Temperature- Measure engine oil temperature
Engine Speed- This is the engine speed in RPM
Engine Temp- Engine Coolant Temperature value
Engine Temp (Actual)- Actual engine coolant temperature value
Engine Torque (Actual)- Calculated actual engine torque
Engine Torque (Delta) - Delta ratio between the actual engine speed and target.
Engine Torque (Target) - Target torque value that the ECU is trying to get too.
Exhaust Gas Temp (Pre Turbo) - EGT value that is modeled, pre turbo.
Exhaust Gas Temp 1- This is the reading of the EGT sensor Bank 1
Exhaust Gas Temp 2- This is the reading of the EGT sensor Bank 2
Fuel Pressure (Actual)- Actual High Pressure Fuel Pressure value
Fuel Pressure (Target) - Target High Pressure Fuel Pressure value.
Fuel Pump (Actual)- PWM duty cycle of the low pressure pump, actual value
Fuel Pump (Target)- PWM duty cycle of the low pressure pump, Target value
Fuel Pump Switch- Switch to determine when the pumps are turned on.
Gear- Transmission Gear Position
Ignition Timing- Ignition angle (BTDC)
Ignition Timing Correction Cylinder 1- Negative knock correction for cylinder 1
Ignition Timing Correction Cylinder 2- Negative knock correction for cylinder 2
Ignition Timing Correction Cylinder 3- Negative knock correction for cylinder 3
Ignition Timing Correction Cylinder 4- Negative knock correction for cylinder 4
Ignition Timing Correction Cylinder 5- Negative knock correction for cylinder 5
Ignition Timing Correction Cylinder 6- Negative knock correction for cylinder 6
Intake Air Temperature- Intake air temperature read through the TMAP sensor.
Intake Cam (Target)- This is the intake camshaft target angle value
Intake Cam 1 (Actual)- Actual intake camshaft target angle value Bank 1
Intake Cam 2 (Actual)- Actual intake camshaft target angle value Bank 2
Lambda Bank 1- Lambda Reading for Bank 1
Lambda Bank 2- Lambda Reading for Bank 2
Large Lift Request- 0 or 1 switch if the ECU is requesting large valve lift. Generally will request it under WOT
MAF- Calculated MAF value
MAF (Per Seg)- Calculated MAF value per segment
MAP (Target) - This is the MAP target setpoint used in the PUT Setpoint table. It is the Y axis.
Oil Pressure (Actual)- Actual oil pressure in the engine
Oil Pressure (Target)- Target oil pressure in the engine
Pedal Position- APP or accelerator pedal position
Predicted Air Mass- This is another calculated MAF value with a higher reading about 1389.
Predicted Torque at Clutch- This is a torque value that is used in factoring in some of the PDK torque safety values.
Throttle Angle (Actual)- Actual throttle angle
Throttle Angle (Target)- Target throttle angle
Trans Oil Temp- PDK Transmission fluid temperature
Turbo Protection- Value that will signal if the ECU is using any of the turbo protection tables.
VTG Bank 1 (Actual)- VTG duty cycle actual value for Bank 1
VTG Bank 1 (Target)- VTG duty cycle target value for Bank 1
VTG Bank 2 (Actual)- VTG duty cycle actual value for Bank 2
VTG Bank 2 (Target)- VTG duty cycle actual value for Bank 2
Vehicle Speed- Vehicle Speed

AP3-POR-007: (981) Cayman/Boxster Data Monitors

**Bolded items indicate an automatically set Accessport default data log parameter

Ambient Air Pressure- Ambient Air Pressure from ECU
Engine Load- Engine load value from 0-100%
Engine Oil Temp- Measure engine oil temperature
Engine Speed- This is the engine speed in RPM
Engine Temp- Engine Coolant Temperature value
Engine Temp (Actual)- Actual engine coolant temperature value
Engine Torque (Delta)- Delta ratio between the actual engine speed and target.
Engine Torque (Target)- Target torque value that the ECU is trying to reach.
Exhaust Gas Temp 1- This is the reading of the EGT sensor Bank 1
Exhaust Gas Temp 2- This is the reading of the EGT sensor Bank 2
Fuel Pressure (Actual)- Actual High Pressure Fuel Pressure value
Fuel Pressure (Target) - Target High Pressure Fuel Pressure value.
Fuel Pump (Actual)- PWM duty cycle of the low pressure pump, actual value
Fuel Pump (Target)- PWM duty cycle of the low pressure pump, Target value
Fuel Pump Switch- Switch to determine when the pumps are turned on.
Gear- Transmission Gear Position
Ignition Timing- Ignition angle (BTDC)
Ignition Timing Correction Cylinder 1- Negative knock correction for cylinder 1
Ignition Timing Correction Cylinder 2- Negative knock correction for cylinder 2
Ignition Timing Correction Cylinder 3- Negative knock correction for cylinder 3
Ignition Timing Correction Cylinder 4- Negative knock correction for cylinder 4
Ignition Timing Correction Cylinder 5- Negative knock correction for cylinder 5
Ignition Timing Correction Cylinder 6- Negative knock correction for cylinder 6
Injector Fuel Flow- Amount of fuel delivered across all banks in lph.
Intake Air Temperature- Intake air temperature read through the TMAP sensor.
Intake Cam (Target)- This is the intake camshaft target angle value
Intake Cam 1 (Actual)- Actual intake camshaft target angle value Bank 1
Intake Cam 2 (Actual)- Actual intake camshaft target angle value Bank 2
Lambda Bank 1- Lambda Reading for Bank 1
Lambda Bank 2- Lambda Reading for Bank 2
Large Lift Request- 0 or 1 switch if the ECU is requesting large valve lift. Generally will request it under WOT
Long Term Fuel Trim Bank 1- Long term trims for bank 1.
Long Term Fuel Trim Bank 2- Long term trims for bank 2.
MAF- Calculated MAF value
MAF (Per Seg)- Calculated MAF value per segment
MAF Bank 1- MAF for bank 1
MAF Bank 2- MAF for bank 2
MAP (Actual)- Actual pressure seen at intake manifold in absolute pressure.
MAP (Target)- This is the MAP target in absolute pressure.
Oil Pressure (Actual)- Actual oil pressure in the engine
Oil Pressure (Target)- Target oil pressure in the engine
Pedal Position- APP or accelerator pedal position
Predicted Air Mass- This is another calculated MAF value with a higher reading about 1389.
Predicted Maximum Torque at Clutch- This is a torque value that is used in factoring in some of the PDK torque safety values.
Throttle Angle (Actual)- Actual throttle angle
Throttle Angle (Target)- Target throttle angle
Trans Oil Temp- PDK Transmission fluid temperature
VIM Actual- Actual value output by ECU
VIM Equipped Engine- If this vehicle is equipped with VIM. All 3.4L and 3.8L have VIM
VIM Position- Tells if VIM is open or closed. Value of 255 is closed, 0 is open.
Vehicle Speed- Vehicle Speed

AP3-POR-007: (991.1) Carrera Data Monitors

**Bolded items indicate an automatically set Accessport default data log parameter

Ambient Air Pressure- Ambient Air Pressure from ECU
Engine Load- Engine load value from 0-100%
Engine Oil Temp- Measure engine oil temperature
Engine Speed- This is the engine speed in RPM
Engine Temp- Engine Coolant Temperature value
Engine Temp (Actual)- Actual engine coolant temperature value
Engine Torque (Delta)- Delta ratio between the actual engine speed and target.
Engine Torque (Target)- Target torque value that the ECU is trying to reach.
Exhaust Gas Temp 1- This is the reading of the EGT sensor Bank 1
Exhaust Gas Temp 2- This is the reading of the EGT sensor Bank 2
Fuel Pressure (Actual)- Actual High Pressure Fuel Pressure value
Fuel Pressure (Target) - Target High Pressure Fuel Pressure value.
Fuel Pump (Actual)- PWM duty cycle of the low pressure pump, actual value
Fuel Pump (Target)- PWM duty cycle of the low pressure pump, Target value
Fuel Pump Switch- Switch to determine when the pumps are turned on.
Gear- Transmission Gear Position
Ignition Timing- Ignition angle (BTDC)
Ignition Timing Correction Cylinder 1- Negative knock correction for cylinder 1
Ignition Timing Correction Cylinder 2- Negative knock correction for cylinder 2
Ignition Timing Correction Cylinder 3- Negative knock correction for cylinder 3
Ignition Timing Correction Cylinder 4- Negative knock correction for cylinder 4
Ignition Timing Correction Cylinder 5- Negative knock correction for cylinder 5
Ignition Timing Correction Cylinder 6- Negative knock correction for cylinder 6
Injector Fuel Flow- Amount of fuel delivered across all banks in lph.
Intake Air Temperature- Intake air temperature read through the TMAP sensor.
Intake Cam (Target)- This is the intake camshaft target angle value
Intake Cam 1 (Actual)- Actual intake camshaft target angle value Bank 1
Intake Cam 2 (Actual)- Actual intake camshaft target angle value Bank 2
Lambda Bank 1- Lambda Reading for Bank 1
Lambda Bank 2- Lambda Reading for Bank 2
Large Lift Request- 0 or 1 switch if the ECU is requesting large valve lift. Generally will request it under WOT
Long Term Fuel Trim Bank 1- Long term trims for bank 1.
Long Term Fuel Trim Bank 2- Long term trims for bank 2.
MAF- Calculated MAF value
MAF (Per Seg)- Calculated MAF value per segment
MAF Bank 1- MAF for bank 1
MAF Bank 2- MAF for bank 2
MAP (Actual)- Actual pressure seen at intake manifold in absolute pressure.
MAP (Target)- This is the MAP target in absolute pressure.
Oil Pressure (Actual)- Actual oil pressure in the engine
Oil Pressure (Target)- Target oil pressure in the engine
Pedal Position- APP or accelerator pedal position
Predicted Air Mass- This is another calculated MAF value with a higher reading about 1389.
Predicted Maximum Torque at Clutch- This is a torque value that is used in factoring in some of the PDK torque safety values.
Throttle Angle (Actual)- Actual throttle angle
Throttle Angle (Target)- Target throttle angle
Trans Oil Temp- PDK Transmission fluid temperature
VIM Actual- Actual value output by ECU
VIM Equipped Engine- If this vehicle is equipped with VIM. All 3.4L and 3.8L have VIM
VIM Position- Tells if VIM is open or closed. Value of 255 is closed, 0 is open.
Vehicle Speed- Vehicle Speed

AP3-POR-008: (987.2 / 997.2) Cayman/Boxster S, Cayman R, Boxster Spyder, Carrera Data Monitors

**Bolded items indicate an automatically set Accessport default data log parameter

*Items are separated into blocks (G01, G0F, etc..). Limiting the number of blocks will increase sample frequency. Whether one item in a block is queried or all of them the logging speed will not change so try and group as many items in as little blocks as possible. This is why you may notice duplicates of some monitors. EX. Choosing (G02) Engine Speed and (G02) Oil Pressure will log faster than selecting (G27) Engine Speed and (G02) Oil Pressure.

(G01) Ambient Pressure-DME - This value is measured by the ambient pressure sensor in the DME control unit and is used to calculate the altitude correction factor. The altitude correction factor is used to inhibit secondary air, tank vent valve and fuel tank leakage diagnosis. If the mass air flow sensor (MAF) fails, a substitute value for the air mass is formed from the engine speed, throttle position and altitude correction factor. The measuring range is from 400 mbar to 1200 mbar.
(G01) Coolant Temp - The coolant temperature is calculated from the voltage signal of the engine temperature sensor and is used to correct the DME maps in accordance with the temperature. The temperature is passed on to the gateway control unit via CAN. It is also used as the basis for thermostat diagnosis. (The warm-up phase is monitored using a temperature model.) If there is no signal, a substitute value is formed in the DME control unit and is then displayed here.
(G01) Fuel Pressure - The fuel high-pressure value, measured by the fuel pressure sensor, is displayed here. The flow control valve at the fuel high-pressure pump regulates the fuel pressure from approx. 40,000 mbar at idle speed up to 120,000 mbar at full throttle. The diagnosis monitors the deviation between the required and actual value.
(G02) AT Flag - Flag that determines if the car has an auto transmission or not.
(G02) Battery Voltage - Supply voltage at terminal 15 on the DME control unit. If a limit value is not reached, the idle speed of the engine can be increased in order to improve the load balance.
(G02) Engine Speed - The actual value of the current engine speed is measured via the pulse sender on the flywheel (60 - 2 pulses per revolution).
(G02) Oil Pressure - Absolute engine oil pressure incl. ambient pressure. Approx. 1,000 mbar (ambient pressure) must be subtracted for the relative engine oil pressure (overpressure). This then corresponds to the value displayed on the instrument cluster.
(G02) Vehicle Speed - Current vehicle speed. The vehicle speed comes from ABS/ASR/PSM via CAN. This is used as an input requirement for various diagnoses and as freeze frame content.
(G04) Actual Throttle Plate Position - The actual throttle valve angle is the opening angle recorded by the throttle valve potentiometer (° throttle valve angle), approx. 0.00 ° (throttle valve fully closed) to 80.00 ° (at full throttle position).
(G04) Target Throttle Plate Position - Requested throttle position.
(G07) Actual Fuel Pressure - The fuel high-pressure value, measured by the fuel pressure sensor, is displayed here. The flow control valve at the fuel high-pressure pump regulates the fuel pressure from approx. 40,000 mbar at idle speed up to 120,000 mbar at full throttle. The diagnosis monitors the deviation between the required and actual value.
(G07) Target Fuel Pressure - Target fuel pressure.
(G0B) Intake Cam Timing B1- The actual camshaft angle is the position of the intake camshafts recorded by the hall senders. An actual value of approx. 125.00 °crk is displayed at idle speed. This value can change to approx. 85.00 °crk during acceleration at full throttle. This results in an adjustment value of approx. 0.00 °crk at idle speed and up to 40.00 °crk at full throttle.
(G0B) Intake Cam Timing B2- The actual camshaft angle is the position of the intake camshafts recorded by the hall senders. An actual value of approx. 125.00 °crk is displayed at idle speed. This value can change to approx. 85.00 °crk during acceleration at full throttle. This results in an adjustment value of approx. 0.00 °crk at idle speed and up to 40.00 °crk at full throttle.
(G0B) Intake Camshaft Phase B1- Measured cam phase bank 1.
(G0B) Intake Camshaft Phase B2 - Measured cam phase bank 2.
(G0F) Actual Clutch Torque- Actual torque value at the clutch.
(G0F) Gear Shift Sync Speed Setpoint - Setpoint requested to sync the shift speed.
(G0F) Requested Fuel - Requested fuel consumption.
(G0F) Target Clutch Torque- Torque targeted at the clutch.
(G0F) Target Fuel Mass - Target fuel mass.
(G10) Air Fuel Trim B1 - Fuel trim bank 1
(G10) Air Fuel Trim B2 - Fuel trim bank 2
(G10) Long Term Fuel Trim B1 - Long term fuel trim bank 1
(G10) Long Term Fuel Trim B2 - Long term fuel trim bank 2
(G11) Short Term Fuel Trim B1 - Short term fuel trim bank 1
(G11) Short Term Fuel Trim B2 - Short term fuel trim bank 2
(G16) Adaptive Fuel Mass - Adapted fuel mass.
(G17) Knock Retard Cyl 1 – Amount of timing being retarded Cylinder 1
(G17) Knock Retard Cyl 2 – Amount of timing being retarded Cylinder 2
(G17) Knock Retard Cyl 3 – Amount of timing being retarded Cylinder 3
(G17) Knock Retard Cyl 4 – Amount of timing being retarded Cylinder 4
(G17) Knock Retard Cyl 5 – Amount of timing being retarded Cylinder 5
(G17) Knock Retard Cyl 6 – Amount of timing being retarded Cylinder 6
(G18) Actual Ignition Angle - Actual ignition timing of the car.
(G18) Average ADV1 Value - Average ADV1 Value.
(G18) Average Knock Retard - Averaged value of knock retard.
(G18) Target Ignition Angle - Target ignition timing of the car.
(G19) Actual Air Fuel Ratio B1 - Actual lambda value bank 1
(G19) Actual Air Fuel Ratio B2 - Actual lambda value bank 2
(G19) Target Air Fuel Ratio B1 - Target lambda value bank 1
(G19) Target Air Fuel Ratio B2 - Target lambda value bank 2
(G1C) Coolant Temperature - Engine coolant temperature.
(G1C) Engine Speed - Engine Speed in RPM
(G1C) Relative engine load - Engine load used by the ECU.
(G1D) Injection Time 1 Cyl 1 - Injection time for the fuel injection system Cyl 1
(G1D) Injection Time 1 Cyl 2 - Injection time for the fuel injection system Cyl 2
(G1D) Injection Time 1 Cyl 3 - Injection time for the fuel injection system Cyl 3
(G1D) Injection Time 1 Cyl 4 - Injection time for the fuel injection system Cyl 4
(G1D) Injection Time 1 Cyl 5 - Injection time for the fuel injection system Cyl 5
(G1D) Injection Time 1 Cyl 6 - Injection time for the fuel injection system Cyl 6
(G1E) Injection Time 2 Cyl 1 - Injection time 2 for the fuel injection system Cyl 1
(G1E) Injection Time 2 Cyl 2 - Injection time 2 for the fuel injection system Cyl 2
(G1E) Injection Time 2 Cyl 3 - Injection time 2 for the fuel injection system Cyl 3
(G1E) Injection Time 2 Cyl 4 - Injection time 2 for the fuel injection system Cyl 4
(G1E) Injection Time 2 Cyl 5 - Injection time 2 for the fuel injection system Cyl 5
(G1E) Injection Time 2 Cyl 6 - Injection time 2 for the fuel injection system Cyl 6
(G22) EGT at Lambda Sensor B1- Exhaust gas temperature measured at the lambda sensor bank 1
(G23) EGT at Lambda Sensor B2 - Exhaust gas temperature measured at the lambda sensor bank 1
(G27) Engine Speed - The actual value of the current engine speed is measured via the pulse sender on the flywheel (60 - 2 pulses per revolution).
(G36)Target Air Fuel Ratio B1 - Target lambda value bank 1
(G36)Actual Air Fuel Ratio B1 - Actual lambda value bank 1
(G37) Target Air Fuel Ratio B2 - Target lambda value bank 2
(G37) Actual Air Fuel Ratio B2 - Actual lambda value bank 2
(G40) Intake Air Temperature - Measured intake air temperature.
(G40) Oil Temperature - Oil Temperature.
(G43) Predicted Air Mass - Final calculated airflow value.
(G5C) Accelerator Pedal Position - Accelerator Pedal position.
(G6E) Fuel Pump #1 Switch - On/Off flag for fuel pump #1
(G6E) Fuel Pump #2 Switch - On/Off flag for fuel pump #2
(G75) Full Load Switch - Flag that determines if the car is at full load.
(G7D) Actual Engine Torque - Measured Engine Torque.
(G7D) Fast ASR Intervention Torque - Fast ASR intervention torque.
(G7D) Maximum Available Torque - Maximum available torque.
(G7D) Target Engine Torque - Target engine torque.

AP3-POR-009: (95B) Macan Data Monitors

**Bolded items indicate an automatically set Accessport default data log parameter

Ambient Air Pressure - Ambient Air Pressure from ECU
Ambient Air Temp - Temperature of ambient air
Battery Voltage - Voltage reading at ECU
Boost (Target) Possible 1 - Boost Target Low - Boost pressure will usually be above this value and below Boost (Target) Possible 2
Boost (Target) Possible 2 - Boost Target High - Boost pressure will usually be below this value and above Boost (Target) Possible 1
Boost 1 (Pre Throttle) - Boost pressure up throttle actual value
Engine Load - Engine load value from 0-100%
Engine Oil Temperature - Measure engine oil temperature
Engine Speed - This is the engine speed in RPM
Engine Temp - Engine Coolant Temperature value
Exhaust Cam (Target) - Target Exhuast Cam Retard for Bank 1 & Bank 2 - Subtract 150* for retard after TDC
Exhaust Cam B1 (Actual) - Actual Exhaust Cam Retard for Bank 1- Subtract 150* for retard after TDC
Exhaust Cam B1 (Deviation) - Delta between Actual and Target Cam retard for Bank 1
Exhaust Cam B2 (Actual) - Actual Exhaust Cam Retard for Bank 2- Subtract 150* for retard after TDC
Exhaust Cam B1 (Deviation) - Delta between Actual and Target Cam retard for Bank 2
Exhaust Gas Temp (Pre Turbo) - EGT value that is modeled, pre turbo.
Exhaust Gas Temp 1- This is the reading of the EGT sensor Bank 1
Exhaust Gas Temp 2- This is the reading of the EGT sensor Bank 2
Fuel Pressure (Target) - Target High Pressure Fuel Pressure value.
Fuel Pump (Actual)- PWM duty cycle of the low pressure pump, actual value
Fuel Pump #1 Switch- Switch to determine when the pumps are turned on.
Fuel Pump #2 Switch- Switch to determine when the pumps are turned on.
Gear- Transmission Gear Position
Ignition Timing- Ignition angle (BTDC)
Ignition Timing Correction Cylinder 1- Negative knock correction for cylinder 1
Ignition Timing Correction Cylinder 2- Negative knock correction for cylinder 2
Ignition Timing Correction Cylinder 3- Negative knock correction for cylinder 3
Ignition Timing Correction Cylinder 4- Negative knock correction for cylinder 4
Ignition Timing Correction Cylinder 5- Negative knock correction for cylinder 5
Ignition Timing Correction Cylinder 6- Negative knock correction for cylinder 6
Intake Air Temp - Intake air temperature read through the TMAP sensor.
Intake Cam B1 (Actual) - Actual Intake Cam Advance for Bank 1 - Subtract from 126* for advance before TDC.
Intake Cam B1 (Deviation) - Delta between Actual and Target Cam advance for Bank 1
Intake Cam B2 (Actual) - Actual Intake Cam Advance for Bank 2 - Subtract from 126* for advance before TDC.
Intake Cam B2 (Deviation) - Delta between Actual and Target Cam advance for Bank 2
Intake Cam (Target) - Target Intake Cam Advance for Bank 1 & Bank 2 - Subtract from 126* for advance before TDC.
Lambda Bank 1- Lambda Reading for Bank 1
Lambda Bank 2- Lambda Reading for Bank 2
MAF - Calculated MAF value
MAF (Per Seg) - Calculated MAF value per segment
MAF Total - Overall MAF value for both banks.
Pedal Position- APP or accelerator pedal position
Short Term Fuel Trim Bank 1 - Short term percentage of fuel added/removed to hit target Labmda for Bank 1.
Short Term Fuel Trim Bank 2 - Short term percentage of fuel added/removed to hit target Labmda for Bank 2.
Throttle Angle (Actual)- Actual throttle angle
Throttle Angle (Target)- Target throttle angle
Trans Oil Temp- PDK Transmission fluid temperature
Turbo Protection- Value that will signal if the ECU is using any of the turbo protection tables.
Vehicle Speed- Vehicle Speed
Wastegate Actuation - % of wastegate activation.

AP3-POR-009: (95B) Macan Base 2.0L Data Monitors

**Bolded items indicate an automatically set Accessport default data log parameter

AFR- Actual Air/fuel ratio based on the front oxygen sensor.
AFR Set Point - ECU's calculated air fuel target set point.
Accel Pedal Position- Accelerator pedal opening angle percentage as determined by the accelerator position sensor.
Air Mass Intake Manifold kgh- Calculated air mass in KG/H.
Air Mass Intake Manifold Per Stroke- Current load value achieved by the ECU used as an axis reference.
Air Mass Intake Manifold Set Point- Mass air lower limit set point
Air Mass Limit Per Stroke Turbo- Turbo protection air mass limit.
Air Mass Per Stroke Set Point- Reference set point for maximum air mass request per stroke.
Ambient Air Temp.- Ambient temperature reading.
Ambient Pressure- Ambient pressure reading used for altitude calculation and compensations.
Battery Voltage- Current battery/charging system voltage.
Boost Pressure- Gauge Pressure readings from MAP sensor. (This monitor only displays pressure values. See: Intake Manifold Pressure for related vacuum readings)
Charge Air Temperature- Modeled Charge air temperature.
Combustion Mode- Current ECU combustion state.
Compressor Inlet Press.- Modeled turbo compressor inlet pressure.
Coolant Temp.- Engine coolant temperature.
Coolant Temp. for Torque Limiting- ECU's current calculated limit value used for torque limiting.
Current Gear- Current calculated gear.
Driver Mode Switch- Current status of driver performance switch (1= Normal/Individual 8= Sport )
Driver Requested Torque- Current calculated driver requested torque from maximum torque tables.
Driver Requested Torque Scalar- Calculated torque scalar from driver interpretation maps.
EGT Upstream Turbo- Modeled exhaust gas temperature in the manifold.
Engine Oil Temp.- Engine oil temperature.
Engine Speed- Engine speed in crankshaft revolutions per minute based on the crankshaft position sensor.
Engine Speed Limit- Current limit from ECU limits tables.
Engine/Vehicle Speed Ratio- Calculated ratio used in traction and diagnostic systems.
Exhaust Cam Position- Current exhaust cam position.
Exhaust Gas Pressure Set Point- Modeled Airflow mass set point.
Exhaust Pressure Flow Factor- Calculated exhaust pressure used in turbo modeling system.
Gear Lever Position- Current actual gear lever position.
Gearbox Oil Temp- Transmission temperature.
HPFP Controller Output- Current ECU commanded state for the HPFP system.
HPFP Effective Pump Volume- Modeled HPFP volume.
IAT- Actual Intake air temperature.
Ignition Correction from Cmb Mode- Corrected basic ignition angle for current combustion mode per intake cylinder.
Ignition Correction from Temperature- Calculated correction due to temperature compensations.
Ignition Table Output- Direct output from current blended table.
Ignition Timing Average- Average ignition after compensations.
Ignition Timing Cylinder 1- Current cylinder 1 ignition timing.
Ignition Timing Cylinder 2- Current cylinder 2 ignition timing.
Ignition Timing Cylinder 3- Current cylinder 3 ignition timing.
Ignition Timing Cylinder 4- Current cylinder 4 ignition timing.
Ignition Timing (Final)- Final ignition after compensations.
Ignition Torque SP Efficiency Vlft High- Setpoint ignition efficiency (VVL position dependant)
Intake Cam Position- Current intake cam position.
Intake Manifold Pressure- Intake manifold pressure used in the boost control system.
Intake Manifold Pressure Delta from Modeled- Calculated deviation pressure from model.
Intake Manifold Pressure Set Point- Calculated intake manifold pressure used in the boost control system.
Intake Pressure Flow Factor- Intake manifold pressure flow factor used in the boost control system.
Knock Dataset Selection- Dataset selection for filtering frequency, depending on injection mode different filter can be selected dynamically.
Knock Retard Cyl. 1- Knock Retard for cylinder 1
Knock Retard Cyl. 2- Knock Retard for cylinder 2
Knock Retard Cyl. 3- Knock Retard for cylinder 3
Knock Retard Cyl. 4- Knock Retard for cylinder 4
LPFP Actual Duty Cycle- Duty cycle of LPFP system.
LPFP Flow Set Point-
LPFP Requested Duty Cycle- ECU's low pressure fuel pump duty cycle request.
LTFT- Long term fuel trims stored by ecu. ( Value of 1 = 0% correction | Value of 1.1 = 10% fuel added | Value of 90 = -10% fuel removed)
Lateral Acceleration- measured in m/s^2
Load Set Point Fast- limited torque request for fast path. The torque requests for slow and fast path are limited by torque monitoring in case of detected failures.
Load Set Point Slow- limited torque request for slow path. The torque requests for slow and fast path are limited by torque monitoring in case of detected failures.
Longitudinal Acceleration- measured in m/s^2
Mass Flow Limit for Torque Intervention 1- Current calculated mass air flow limit from load tables for torque limit intervention.
Mass Flow Limit for Torque Intervention 2- Current calculated mass air flow limit from load tables for torque limit intervention.
Mass Flow Limit for Torque Intervention 3- Current calculated mass air flow limit from load tables for torque limit intervention.
Mass Flow Limit for Torque Intervention 4- Current calculated mass air flow limit from load tables for torque limit intervention.
Mass Flow Through Catalyst- Modeled airflow through catalyst used for system protection functions.
Mass Fuel Flow Set Point- Calculated mass fuel set point for fueling system modeling.
Max PUT from Turbo Protection- Maximum pressure upstream throttle request from the ECU for turbo protection, from turbo protection folder.
Maximum Possible PUT-
Maximum Torque Overheating Protection- Maximum torque request modeled for overheat protection.
Maximum Torque at Clutch- Maximum torque request at clutch from the maximum torque tables.
Maximum Turbo Speed Set Point- Maximum turbo speed modeled for turbo protection.
PUT Modeled- Modeled pressure request from ECU
PUT Set Point- Final pressure request after compensations.
Pressure Ratio at Compressor- Current calculated pressure ratio.
Pressure Ratio at Compressor Set Point- Current calculated set point pressure ratio.
Pressure Ratio vs Ambient- Current calculated pressure ratio to ambient for boost control system.
Pressure Upstream Throttle- Calculated pressure upstream throttle for boost control system.
Put Additive Correction- Compensation to PUT for atmospheric conditions.
Rail Pressure- Fuel rail pressure.
Rail Pressure Set Point- Actual fuel pressure request.
Rail Pressure Set Point Delta- Deviation from the fuel pressure setpoint and measured fuel pressure.
Reduced Volume Flow Pre Turbo-
Relative Engine Load- Relative engine load value calculated by airflow.
Relative Load- Current engine load for full load detection.
STFT- Current fuel trim stored and calculated by the ECU.
Steering Angle- Steering wheel angle from center.
TPS- Actual throttle angle.
TPS Set Point- Throttle angle set point.
Target Filling- Target calculated cylinder filling used in load targeting and calculation.
Throttle Pressure Ratio- Throttle pressure ratio used in WGDC and load calculations.
Throttle Pressure Ratio Set Point- Throttle pressure ratio set point used in WGDC and load calculations.
Time at Full Load- Timer for full load operation.
Torque (Actual)- Calculated current torque output.
Torque Indicated Basic- Modeled base torque calculation.
Torque Limit Turbo Overheat Protection- Torque limit for turbo overheat protection from protection tables.
Torque Limit Turbo Protection- Torque limit for turbo protection from torque protection tables.
Torque Limitation Source- Current source for ECU requested torque limitation. These values can stand alone or can add together as well. For instance a value of 96 would be both 32 and 64 set. See below for states:
16384 = Permanent torque limitation because of too high exhaust gas temperature
8192 = Permanent torque limitation because of boost pressure actuator related error
2048 = Permanent torque limitation because of too high charger speed
1024 = Permanent torque limitation because of error via FARM
512 = Permanent torque limitation because of too high intake air temperature
256 = Temporary torque limitation because of high charger speed
128 = Temporary torque limitation because of operation at maximum charge pressure ratio
64 = Temporary torque limitation because of operation at maximum absolute charge air pressure setpoint
32 = Temporary torque limitation because of high intake air temperature
0 = None
Torque Maximum Clutch- Calculated maximum torque derived from torque tables.
Torque Maximum Engine- Calculated maximum torque derived from torque tables.
Torque Maximum Indicated- Calculated maximum torque modeled.
Torque Reference- Calculated modeled torque.
Torque Reference Maximum- Calculated maximum torque.
Torque Value for Air Mass Set Point- Torque value modeled from current calculated air mass.
Torque at Clutch- Modeled torque at the clutches.
Turbine Actuator Base Value- Actuator set point value pre-compensation.
Turbine Actuator Closed Loop Mod- Compensation factor for turbine actuator.
Turbine Actuator Final Value- WGDC actuator position result after PID correction
Turbine Actuator Integral- Current calculated waste gate duty cycle integral factor.
Turbine Actuator Proportional- Current calculated waste gate actuator position proportional factor.
Turbine Actuator Raw Output- Raw value for turbine actuator position request.
Turbine Actuator Set Point Regular Mode-
Turbine Power Factor Set Point- Current turbine control factor.
Turbo Shaft Speed- Modeled turbo shaft speed from lookup tables.
Turbo Speed Max differential- The turbocharger speed delta to maximum turbocharger speed setpoint to aid protection.
Turbo Speed Set Point- Turbo speed set point from turbo modeling tables.
Valve Lift Set Point- Valve lift set point request from base tables.
Valve Lift State- Valve High lift position (1= High lift 0= Normal)
Vehicle Speed- Current Vehicle Speed
Wastegate Mass Flow Set Point- Mass air flow set point for turbine actuator position calculation.
Wheel Speed FL- Wheel speed sensor signal - Front left.
Wheel Speed FR- Wheel speed sensor signal - Front right.
Wheel Speed RL- Wheel speed sensor signal - Rear left.
Wheel Speed RR- Wheel speed sensor signal - Rear right.

AP3-POR-

PDK: (981/991.1/987.2/997.2) PDK Data Monitors
**Logging PDK can slow datalogging speeds, for this reason PDK does not contain a default log list.
(PDK) Shaft Speed Odd Gears - Input shaft RPM (odd gears).
(PDK) Shaft Speed Even Gears - Input shaft RPM (even gears).
(PDK) Clutch Pressure Odd - Measurement of pressure applied to odd clutches.
(PDK) Clutch Pressure Even - Measurement of pressure applied to even clutches.
(PDK) Clutch Pressure Reservoir - Measurement of clutch pressure reservoir.
(PDK) Shiftrod Displacement Sensor 1 - Shift rod 1 is used for 4th and 6th gear.
(PDK) Shiftrod Displacement Sensor 2 - Shift rod 2 is used for 5th and 7th gear.
(PDK) Shiftrod Displacement Sensor 3 - Shift rod 3 is used for 1st and 3rd gear.
(PDK) Shiftrod Displacement Sensor 4 - Shift rod 4 is used for 2nd and reverse.
(PDK) Filtered Pressure Sensor Supply Voltage - Voltage supplied to pressure sensors, generally static at 5v +/- .05v.
(PDK) Filtered Speed Sensor Supply Voltage - Voltage supplied to speed sensors, generally static at 8.5v +/- .05v.
(PDK) Filtered Battery Voltage - Measured battery voltage.
(PDK) Fluid Temperature - Temperature of PDK gear oil.
(PDK) Highside Voltage 0 - Voltage supply to solenoids.
(PDK) Highside Voltage 1 - Voltage supply to solenoids.
(PDK) Highside Voltage 2 - Voltage supply to solenoids.
(PDK) Highside Voltage 3 - Voltage supply to solenoids.
(PDK) Actual Measured Current 0 - Amperage supplied to odd gear clutch pressure solenoid.
(PDK) Actual Measured Current 1 - Amperage supplied to even gear clutch pressure solenoid.
(PDK) Actual Measured Current 2 - Amperage supplied to unknown pressure solenoid.
(PDK) Actual Measured Current 3 - Amperage supplied to unknown pressure solenoid.
(PDK) Actual Measured Current 4 - Amperage supplied to unknown pressure solenoid.
(PDK) Actual Measured Current 5 - Amperage supplied to unknown pressure solenoid.
(PDK) Actual Measured Current 6 - Amperage supplied to unknown pressure solenoid.
(PDK) Engine RPM - Engine speed.
(PDK) APP - Accelerator pedal position.
(PDK) Wheel Speed FL - Front left wheel speed.
(PDK) Wheel Speed FR - Front right wheel speed.
(PDK) Wheel Speed RL - Rear left wheel speed.
(PDK) Wheel Speed RR - Rear right wheel speed.
(PDK) Gear (For Traction) - Gear requested based on conditions.
(PDK) Gear (Requested) - Next gear requested.
(PDK) Gear (Display) - Gear that is displayed on instrument cluster.
(PDK) Output Shaft RPM - RPM of the transmission output shaft.
(PDK) Race Starts Counter (Clutch) - Amount of Race Starts on Clutch, gets reset after clutch adaption.
(PDK) Race Starts Counter (Gear Box) - Amount of Race Starts on Transmission, gets reset after clutch adaption.
AP3-POR-010:
AP3-POR-011:
AP3-POR-012:
Accelerator Pedal Position (Actual) - Accelerator pedal opening angle percentage as determined by the accelerator position sensor.
Accelerator Pedal Position (Target)
Ambient Air Pressure - Ambient air pressure (barometric pressure)
Ambient Air Temp - Ambient Air Temperature
Battery Voltage - Battery Voltage
Best Response Mode - Mode in which to spool the trubo for best response.
Boost 1 (Pre-Throttle) - Pressure measured in the intake post turbo and before the throttle (values spike at throttle closure)
Boost Filtered - Boost pressure with a filter value added in.
Boost Pre-Throttle (Limit) - Boost PUT limit
Boost Pre-Throttle (target) -Targeted pressure before the throttle
Brake Pressure - Line pressure applied to the brakes
Engine Speed - Engine Speed in revolutions Per Minute
Engine Load - The demand asked of the engine based on airflow and throttle position
Engine Oil Temp - Temperature of engine Oil
Engine Torque (Actual 2) - Actual Engine Torque 2
Engine Torque (Actual) - Actual Engine Torque 1
Engine Torque (Basic) - The base engine torque value
Engine Torque (Indicated) - TQI - A calculated level of torque
Engine Torque (Limitation 2) - The limit of how much torque will be allowed under certain conditions
Engine Torque (Limitation) - The limit of how much torque will be allowed under certain conditions
Engine Torque ((Mass Air Flow Calc) - This is the value of how much airflow is used for the mass air flow calculations
Engine Torque (Max Allowed) - Maximum allowed engine torque
Engine Torque (Max at Clutch) - Maximum allowed engine torque at the clutch
Exhaust Cam (Target) - Targeted position for exhaust cam
Exhaust Cam B1 (Actual) - Actual position for exhaust cam bank 1
Exhaust Cam B2 (Actual) - Actual position for exhaust cam bank 2
Exhaust Gas Temp (Pre Turbo) - Actual temperature of exhaust before the turbo
Fuel Cut (Authorize) - This is a flag to allow a fuel cut to happen
Fuel Cut (Enabled) - This is a flag that says a fuel cut is happening
Fuel Cut (Inhibit) - This will not allow the engine to cut fuel
Fuel Pressure (Actual) - Measured fuel pressure in the lines Actual value
Fuel Pump (Actual) - Fuel pump PWM duty cycle for low pressure pump Actual value
Gear - Transmission Gear Position
Ignition RON - An arbitrary value that increases as the learned knock increases, the higher the value the less timing the car will run based on a learned fuel quality.
Ignition Timing Correction Cyl1 - Measure of negative knock correction for cylinder 1
Ignition Timing Correction Cyl2 - Measure of negative knock correction for cylinder 2
Ignition Timing Correction Cyl3 - Measure of negative knock correction for cylinder 3
Ignition Timing Correction Cyl4 - Measure of negative knock correction for cylinder 4
Ignition Timing Correction Cyl5 - Measure of negative knock correction for cylinder 5
Ignition Timing Correction Cyl6 - Measure of negative knock correction for cylinder 6
Ignition Timing - Angle of rotation when spark is fired
Injection Time 1 - Angle of rotation when injector is fired
Injection Time 2 - Angle of rotation when injector is fired for double injection
Injection Time 3 - Angle of rotation when injector is fired for triple injection
Intake Air Temp - Temperature of air going into the vehicle's intake
Intake Cam (Target) -Target angle for intake camshaft
Intake Cam B1 (Actual) - Actual angle for intake camshaft bank 1
Intake Cam B2 (Actual) - Actual angle for intake camshaft bank 2
Lambda Bank 1 - Air Fuel Ratio of bank 1
Lambda Bank 2 - Air Fuel Ratio of bank 2
Lambda pre CAT B2 (Target) - Air fuel ratio target taken before the cat on bank 2
lv_lamb_torque_ctl - Lambda (AFR_ cut is active to control torque
lv_tq_dyn_iga - Ignition timing is used to control torque
lv_tq_dyn_scc - Active sequential cylinder cut enabled to limit torque
lv_tq_lamb_ena - Lambda control to limit torque is enabled flag
lv_tq_lamb_inh - inhibit lambda intervention for torque control
MAF (Per Seg) (4 bytes) - Calculated MAF values 4 bytes long.
MAF Total - Combined total of all MAF variables added together.
MAF - Mass Air Flow measured in mg/stk
MAP (Target) (4 bytes) - MAP setpoint
MAP Filtered (4 bytes) - MAP reading filtered.
Map Measured - Measured MAP value from sensor. This is a SENT sensor.
Predicted Air Mass - Calculated load value used to measure air mass.
Short Term Fuel Trim Bank 1 - Short term fuel corrections applied to bank 1
Short Term Fuel Trim Bank 2 - Short term fuel corrections applied to bank 2
Steering Angle - Position of the steering wheel
Throttle Angle (Actual) - Measured angle of the throttle blade
Throttle Angle (Target) - Target angle of the throttle blade
Torque Reduction Request - A request to limit torque production
tqi_req_fast_dtm - Indicated torque request fast
tqi_req_slow_dtm - Indicated torque request slow
Turbo Charger Rotational Speed (Target Max) - Maximum allowed turbo speed.
Turbo Charger Rotational Speed - Current turbocharger rotational speed (calculated not measured)
Turbo Protection State - State to prevent damage for turbo
Turbocharger Protection Activation - Flag to alert if turbo protection is active
Vehicle Speed - How fast the car is going
Waste Gate Actuation - Duty cycle of wastegate
Wheel Speed (FL) - Speed of the wheel Front Left
Wheel Speed (FR) - Speed of the wheel Front Right
Wheel Speed (RL) - Speed of the wheel Rear Left
Wheel Speed (RR) - Speed of the wheel Rear Right
Yaw - Angle of lean of the car in the vertical axis
B1 (Low FRAU B1) - Low speed long term fuel trim bank 1
B2 (Low FRAU B2) - Low speed long term fuel trim bank 2
010:
AP3-POR-011:
AP3-POR-012:

Accelerator Pedal Position (Actual) - Accelerator pedal opening angle percentage as determined by the accelerator position sensor.
Accelerator Pedal Position (Target)
Ambient Air Pressure - Ambient air pressure (barometric pressure)
Ambient Air Temp - Ambient Air Temperature
Battery Voltage - Battery Voltage
Best Response Mode - Mode in which to spool the trubo for best response.
Boost 1 (Pre-Throttle) - Pressure measured in the intake post turbo and before the throttle (values spike at throttle closure)
Boost Filtered - Boost pressure with a filter value added in.
Boost Pre-Throttle (Limit) - Boost PUT limit
Boost Pre-Throttle (target) -Targeted pressure before the throttle
Brake Pressure - Line pressure applied to the brakes
Engine Speed - Engine Speed in revolutions Per Minute
Engine Load - The demand asked of the engine based on airflow and throttle position
Engine Oil Temp - Temperature of engine Oil
Engine Torque (Actual 2) - Actual Engine Torque 2
Engine Torque (Actual) - Actual Engine Torque 1
Engine Torque (Basic) - The base engine torque value
Engine Torque (Indicated) - TQI - A calculated level of torque
Engine Torque (Limitation 2) - The limit of how much torque will be allowed under certain conditions
Engine Torque (Limitation) - The limit of how much torque will be allowed under certain conditions
Engine Torque ((Mass Air Flow Calc) - This is the value of how much airflow is used for the mass air flow calculations
Engine Torque (Max Allowed) - Maximum allowed engine torque
Engine Torque (Max at Clutch) - Maximum allowed engine torque at the clutch
Exhaust Cam (Target) - Targeted position for exhaust cam
Exhaust Cam B1 (Actual) - Actual position for exhaust cam bank 1
Exhaust Cam B2 (Actual) - Actual position for exhaust cam bank 2
Exhaust Gas Temp (Pre Turbo) - Actual temperature of exhaust before the turbo
Fuel Cut (Authorize) - This is a flag to allow a fuel cut to happen
Fuel Cut (Enabled) - This is a flag that says a fuel cut is happening
Fuel Cut (Inhibit) - This will not allow the engine to cut fuel
Fuel Pressure (Actual) - Measured fuel pressure in the lines Actual value
Fuel Pump (Actual) - Fuel pump PWM duty cycle for low pressure pump Actual value
Gear - Transmission Gear Position
Ignition RON - An arbitrary value that increases as the learned knock increases, the higher the value the less timing the car will run based on a learned fuel quality.
Ignition Timing Correction Cyl1 - Measure of negative knock correction for cylinder 1
Ignition Timing Correction Cyl2 - Measure of negative knock correction for cylinder 2
Ignition Timing Correction Cyl3 - Measure of negative knock correction for cylinder 3
Ignition Timing Correction Cyl4 - Measure of negative knock correction for cylinder 4
Ignition Timing Correction Cyl5 - Measure of negative knock correction for cylinder 5
Ignition Timing Correction Cyl6 - Measure of negative knock correction for cylinder 6
Ignition Timing - Angle of rotation when spark is fired
Injection Time 1 - Angle of rotation when injector is fired
Injection Time 2 - Angle of rotation when injector is fired for double injection
Injection Time 3 - Angle of rotation when injector is fired for triple injection
Intake Air Temp - Temperature of air going into the vehicle's intake
Intake Cam (Target) -Target angle for intake camshaft
Intake Cam B1 (Actual) - Actual angle for intake camshaft bank 1
Intake Cam B2 (Actual) - Actual angle for intake camshaft bank 2
Lambda Bank 1 - Air Fuel Ratio of bank 1
Lambda Bank 2 - Air Fuel Ratio of bank 2
Lambda pre CAT B2 (Target) - Air fuel ratio target taken before the cat on bank 2
lv_lamb_torque_ctl - Lambda (AFR_ cut is active to control torque
lv_tq_dyn_iga - Ignition timing is used to control torque
lv_tq_dyn_scc - Active sequential cylinder cut enabled to limit torque
lv_tq_lamb_ena - Lambda control to limit torque is enabled flag
lv_tq_lamb_inh - inhibit lambda intervention for torque control
MAF (Per Seg) (4 bytes) - Calculated MAF values 4 bytes long.
MAF Total - Combined total of all MAF variables added together.
MAF - Mass Air Flow measured in mg/stk
MAP (Target) (4 bytes) - MAP setpoint
MAP Filtered (4 bytes) - MAP reading filtered.
Map Measured - Measured MAP value from sensor. This is a SENT sensor.
Predicted Air Mass - Calculated load value used to measure air mass.
Short Term Fuel Trim Bank 1 - Short term fuel corrections applied to bank 1
Short Term Fuel Trim Bank 2 - Short term fuel corrections applied to bank 2
Steering Angle - Position of the steering wheel
Throttle Angle (Actual) - Measured angle of the throttle blade
Throttle Angle (Target) - Target angle of the throttle blade
Torque Reduction Request - A request to limit torque production
tqi_req_fast_dtm - Indicated torque request fast
tqi_req_slow_dtm - Indicated torque request slow
Turbo Charger Rotational Speed (Target Max) - Maximum allowed turbo speed.
Turbo Charger Rotational Speed - Current turbocharger rotational speed (calculated not measured)
Turbo Protection State - State to prevent damage for turbo
Turbocharger Protection Activation - Flag to alert if turbo protection is active
Vehicle Speed - How fast the car is going
Waste Gate Actuation - Duty cycle of wastegate
Wheel Speed (FL) - Speed of the wheel Front Left
Wheel Speed (FR) - Speed of the wheel Front Right
Wheel Speed (RL) - Speed of the wheel Rear Left
Wheel Speed (RR) - Speed of the wheel Rear Right
Yaw - Angle of lean of the car in the vertical axis
B1 (Low FRAU B1) - Low speed long term fuel trim bank 1
B2 (Low FRAU B2) - Low speed long term fuel trim bank 2

AP3-POR-PDK: (987.2/981/718/997.2/991.1/991.2) PDK Data Monitors

**Logging PDK can slow datalogging speeds, for this reason PDK does not contain a default log list.

(PDK) Shaft Speed Odd Gears - Input shaft RPM (odd gears).
(PDK) Shaft Speed Even Gears - Input shaft RPM (even gears).
(PDK) Clutch Pressure Odd - Measurement of pressure applied to odd clutches.
(PDK) Clutch Pressure Even - Measurement of pressure applied to even clutches.
(PDK) Clutch Pressure Reservoir - Measurement of clutch pressure reservoir.
(PDK) Shiftrod Displacement Sensor 1 - Shift rod 1 is used for 4th and 6th gear.
(PDK) Shiftrod Displacement Sensor 2 - Shift rod 2 is used for 5th and 7th gear.
(PDK) Shiftrod Displacement Sensor 3 - Shift rod 3 is used for 1st and 3rd gear.
(PDK) Shiftrod Displacement Sensor 4 - Shift rod 4 is used for 2nd and reverse.
(PDK) Filtered Pressure Sensor Supply Voltage - Voltage supplied to pressure sensors, generally static at 5v +/- .05v.
(PDK) Filtered Speed Sensor Supply Voltage - Voltage supplied to speed sensors, generally static at 8.5v +/- .05v.
(PDK) Filtered Battery Voltage - Measured battery voltage.
(PDK) Fluid Temperature - Temperature of PDK gear oil.
(PDK) Highside Voltage 0 - Voltage supply to solenoids.
(PDK) Highside Voltage 1 - Voltage supply to solenoids.
(PDK) Highside Voltage 2 - Voltage supply to solenoids.
(PDK) Highside Voltage 3 - Voltage supply to solenoids.
(PDK) Actual Measured Current 0 - Amperage supplied to odd gear clutch pressure solenoid.
(PDK) Actual Measured Current 1 - Amperage supplied to even gear clutch pressure solenoid.
(PDK) Actual Measured Current 2 - Amperage supplied to unknown pressure solenoid.
(PDK) Actual Measured Current 3 - Amperage supplied to unknown pressure solenoid.
(PDK) Actual Measured Current 4 - Amperage supplied to unknown pressure solenoid.
(PDK) Actual Measured Current 5 - Amperage supplied to unknown pressure solenoid.
(PDK) Actual Measured Current 6 - Amperage supplied to unknown pressure solenoid.
(PDK) Engine RPM - Engine speed.
(PDK) APP - Accelerator pedal position.
(PDK) Wheel Speed FL - Front left wheel speed.
(PDK) Wheel Speed FR - Front right wheel speed.
(PDK) Wheel Speed RL - Rear left wheel speed.
(PDK) Wheel Speed RR - Rear right wheel speed.
(PDK) Gear (For Traction) - Gear requested based on conditions.
(PDK) Gear (Requested) - Next gear requested.
(PDK) Gear (Display) - Gear that is displayed on instrument cluster.
(PDK) Output Shaft RPM - RPM of the transmission output shaft.
(PDK) Race Starts Counter (Clutch) - Amount of Race Starts on Clutch, gets reset after clutch adaption.
(PDK) Race Starts Counter (Gear Box) - Amount of Race Starts on Transmission, gets reset after clutch adaption.

Versions Compared

Old Version 10

New Version 11

Key

Vehicle Support:

AP3-POR-001

AP3-POR-002

AP3-POR-003

AP3-POR-004

AP3-POR-005

AP3-POR-006

AP3-POR-007

AP3-POR-008

AP3-POR-009

AP3-POR-010 | AP3-POR-011 | AP3-POR-

012

AP3-POR-001/004: (997.1/996 Turbo/GT2) Data Monitors

AP3-POR-002: (997.2 Turbo/Turbo S) Data Monitors

AP3-POR-PDK

AP3-POR-001/004: (997.1/996 Turbo/GT2) Data Monitors

AP3-POR-002: (997.2 Turbo/Turbo S) Data Monitors

AP3-POR-003/005: (997.1/997.2 GT3/GT3 RS) Data Monitors

AP3-POR-006: (991.1) Turbo / Turbo S Data Monitors

AP3-POR-007: (981) Cayman/Boxster Data Monitors

AP3-POR-007: (991.1) Carrera Data Monitors

AP3-POR-008: (987.2 / 997.2) Cayman/Boxster S, Cayman R, Boxster Spyder, Carrera Data Monitors

AP3-POR-009: (95B) Macan Data Monitors

AP3-POR-009: (95B) Macan Base 2.0L Data Monitors

AP3-POR-

010:
AP3-POR-011:
AP3-POR-012:

AP3-POR-PDK: (987.2/981/718/997.2/991.1/991.2) PDK Data Monitors

Page Comparison

Versions Compared

Old Version 10

New Version 11

Key

Vehicle Support:

AP3-POR-001

AP3-POR-002

AP3-POR-003

AP3-POR-004

AP3-POR-005

AP3-POR-006

AP3-POR-007

AP3-POR-008

AP3-POR-009

AP3-POR-010 | AP3-POR-011 | AP3-POR-

012

AP3-POR-001/004: (997.1/996 Turbo/GT2) Data Monitors

AP3-POR-002: (997.2 Turbo/Turbo S) Data Monitors

AP3-POR-PDK

AP3-POR-001/004: (997.1/996 Turbo/GT2) Data Monitors

AP3-POR-002: (997.2 Turbo/Turbo S) Data Monitors

AP3-POR-003/005: (997.1/997.2 GT3/GT3 RS) Data Monitors

AP3-POR-006: (991.1) Turbo / Turbo S Data Monitors

AP3-POR-007: (981) Cayman/Boxster Data Monitors

AP3-POR-007: (991.1) Carrera Data Monitors

AP3-POR-008: (987.2 / 997.2) Cayman/Boxster S, Cayman R, Boxster Spyder, Carrera Data Monitors

AP3-POR-009: (95B) Macan Data Monitors

AP3-POR-009: (95B) Macan Base 2.0L Data Monitors

AP3-POR-

010: AP3-POR-011: AP3-POR-012:

AP3-POR-PDK: (987.2/981/718/997.2/991.1/991.2) PDK Data Monitors

010:
AP3-POR-011:
AP3-POR-012: