Image RemovedImage Added

552101 & 552111 – Evo X Catback Exhaust

Mitsubishi Evolution X GSR, FE, MR, SST 2008-2015

Image Modified

Congratulations on your purchase of the COBB Tuning Mitsubishi Evolution X Catback Exhaust! The following instructions will assist you through the installation process. Please read them BEFORE beginning the install to familiarize yourself with the steps and tools needed. If you feel you cannot properly perform this installation, we HIGHLY recommend you take the vehicle to a qualified and experienced automotive technician.

IMPORTANT! Installing this kit will may require custom tuning or utilizing an appropriate Stage Power Package map if you have a matching mechanical configuration. Please consult with COBB or an authorized ProTuner in your area if you have any questions!

Table of Contents

Parts List

• Mid-Pipe
• Muffler Section
• (2) M10x1.25 Bolts
• (2) M10x1.25 Flanged Nuts
• 3" Exhaust Gasket

Tools Needed

• Phillips head screwdriver
• Flathead screwdriver

• 3/8" ratchet

• 3/8" 12mm socket 
  

• 3/8" 14mm socket

• 3/8" 17mm deep socket

• 3/8" 12" extension

• 3/8" 6" extension

• 12mm combination wrench
• (2) 14mm combination wrench
• 17mm combination wrench
• Exhaust Hanger Pliers

Removal of the Stock Cat-Back Exhaust

1.  Chalk  Securely chalk the front wheels and lift the rear of the car, supporting it with jack stands.  Then allow the car to cool properly.
   
   
2. Start by unbolting the mid-pipe section from the cat-pipe using your 17mm.
   Image Removed
   Image Added    Image RemovedImage Added
   
   
   
3. Unhook or unbolt the rear exhaust hanger of the midpipe.
   Image Removed
   Image Added   Image RemovedImage Added
   
   
   
4. Slowly unbolt the two 14mm spring bolts holding the mid-pipe to the muffler.  Once unbolted slowly lower it to the ground.
   Image Removed
   Image Added
   
   
   
5. Remove the exhaust hangers for each side of the muffler and remove the muffler from the car.  Oftentimes it's easiest to get one side close then remove the other side entirely.
   Image Removed
   Image Added   Image RemovedImage Added    Image RemovedImage Added
   
   
   

Installation of the COBB Cat-Back Exhaust

1. Remove the exhaust hangers from the mufflers and add them on to the COBB Muffler
   Image Removed
   Image Added
   
   
   
2. Install the COBB muffler on to the car, once both hangers are on it should stay in place.
   Image Removed
   Image Added
   
   
   
3. Transfer the stock rear exhaust hanger on to the COBB catback mid-pipe
   Image Removed
   Image Added
   
   
   
4. Loosely install the new mid-pipe into the car using the hanger to hold it up in the back.
   Image Removed
   Image Added
   
   
   
5. Using the provided gaskets and hardware bolt the exhaust in place but leave it slightly loose.
   Image Removed
   Image Added
   
   
   
6. Move the muffler around in the hangers until you're happy with the positioning of the exhaust tips.
   Image Removed
   Image Added    Image RemovedImage Added    Image RemovedImage Added
   
   
   
7. Tighten it down the rest of the way using your two 14mm wrenches.
   
   
8. Start the vehicle to test for exhaust leaks.  If no leaks are found, remove the jack stands and lower the vehicle.  Now, go out and enjoy your new COBB Cat-back!
   
   

Related Links