7V2100 - Volkswagen MK7 SF Intake System [Discontinued]

 worddavc31d0bad824f9de614eee804cd01448c.png

7V2100
COBB Tuning MK7 SF Intake 

Congratulations on your purchase of the COBB Tuning Volkswagen MK7 Intake Kit. The following instructions will assist you through your installation process. Please read them first BEFORE beginning the install and familiarize yourself with the steps and tools needed. If you feel that you cannot properly perform this installation, we HIGHLY recommend you take the vehicle to a qualified and experienced automotive technician.




Part List

  • Airbox Body
  • Airbox Lid
  • Snorkel Body
  • Snorkel Lid
  • Silicone Intake Tube
  • Velocity Stack
  • Velocity Stack Bracket
  • Air Filter
  • Air Pump Adapter
  • 1/4" Fitting
  • 11x SS Button Head M4 x 10mm Screw
  • 11x 4mm Black Nylon Washer
  • 5x Flange Bolt M6 x 12mm
  • 2x SS Socket Head M6 x 10mm Screw
  • 2x M6 Lock Washer
  • 2x M6 Flat Washer
  •  #048 Worm Clamp
  •  #044 Worm Clamp
  • 12" Edge Trim
  • 16" Edge Trim Low Profile
  • 3' Edge Trim Rounded Back
  • 2.5mm Hex Key

Tools Needed

  • Ratchet
  • Sockets: 7mm, 8mm, 10mm
  • T20 Torx Screwdriver
  • Nose Clamp Pliers
  • 6mm Hex Key




Removal of Factory Volkswagen MK7 Intake

Before removal of factory intake, it is recommended to remove the engine cover by pulling it off of its grommets.

  1. Inspect the new components included with the COBB kit. If anything appears out of place, please contact COBB immediately and do not proceed with the installation.
  2. Using the nose clamp pliers, take off the clamp holding the stock intake tube to the turbo.  Then pull the tube off of the turbo inlet housing. 
  3. Take a T20 Torx screwdriver and remove the screws holding the stock snorkel in place. 
  4. Pull the 1/4" rubber hose off of the stock airbox. This may require some strength! Just be careful not to bust your hand when it finally comes off!
  5. Unclip the air pump from the stock airbox.
  6. Now you should be able to pull the stock airbox and intake tube out of the car by popping the box off of the grommets that hold it in place. 
  7. Once the airbox and tube are out of the car, you can remove the stock snorkel. 




 Installation of COBB Volkswagen MK7 Intake System

  1. Begin by placing the snorkel body in the stock snorkel location with the lid already attached. Attach the lid by placing (3) M4 button head screws with (3) 4mm black nylon washers in the top 3 threaded PEM nuts. Use a 2.5mm hex key to loosely thread in the screws. The easiest way to install the snorkel is by sliding the snorkel into the correct location at an angle shown in the following picture. Make sure that the snorkel fits under the plastic lip on the car. 



  2. Using (2) M4 button head screws and (2) 4mm black nylon screws, install the airbox to the car in the stock snorkel mounting locations. Use a 2.5mm hex key to tighten the screws. Once the two mounting screws are in place, you can now tighten all of the screws holding the snorkel lid to the snorkel.



  3. Take the air pump adapter and place it onto the air pump. Then move the air pump hose over to its new location and plug into the silicone intake tube provided. Also place the 1/4" fitting into the correct location on the silicone tube and connect the 1/4" rubber hose to this fitting. Once these are connected to the tube, move the tube as far away from where the airbox will install as possible. NOTE: Do not install the intake tube onto the turbo inlet yet. 



  4. Cut a piece of trim to about 12" and put it around the hole the intake tube will go through.



  5. Cut two pieces to around 4" long and fit them to the holes in the bottom and side tab of the airbox.  In order to get the one to sit in the side tab neatly, you may need to rim it slightly.

        


  6. Cut two pieces to 2" and add them into the slot cutouts where the radiator hose will rest.

        

  7. Now, place the airbox in the car. Make sure that the stock grommet mounts go through the hole cutouts on the base of the box and that the airbox inlet goes around the snorkel outlet. You will need to install the airbox at an angle to where the side mounting tab first goes underneath the ECU harness. The airbox mounting tabs should fit on the exterior of the mounting tabs on the snorkel. 

            

  8. Take 4 M6 flange bolts and thread them into the PEM nuts shown to secure the airbox to the snorkel. To ease installation, remove the wiper fluid reservoir by popping it out of the hole shown and by unclipping it from the car. Use a 10mm wrench or socket to tighten the flange bolts. (NOTE: The hardware depicted in this step are incorrect! You should have fancier hardware!)

                

  9. Install the velocity stack bracket to the base of the airbox using a M6 flange bolt. Tighten in the orientation shown. (NOTE: The hardware depicted in this step are incorrect! You should have fancier hardware!)



  10. Now take (2) M6 lock washers and the (2) M6 button head cap screws and connect the velocity stack to the bracket. Use a 6mm hex key to tighten the screws. 



  11. Place the silicone tube into rear cutout of the airbox. Then insert the velocity stack into the silicone tube. Make sure that a #048 worm clamp is placed on the silicone before installation so that you will be able to tighten the silicone onto the velocity stack. Use an 8mm socket to tighten.



  12. Using a #044 worm clamp, secure the silicone intake tube to the turbo inlet. Use an 8mm socket to tighten. 



  13. Install the air filter provided by placing onto the velocity stack and tightening the worm clamp using a flathead screwdriver. 



  14. Now, take the radiator hose and place it in the slot cutouts on the airbox. 

  15. Cut the edge trim provided to match the length of the front of the lid.



  16. Now you can install the lid onto the airbox using 6 M4 button head cap screws and 6 4mm black nylon washers. Lightly thread in the screws until you are able to line the lid up with the edges of the airbox. Once everything is in line, tighten using a 2.5mm hex key. 



  17. Check to make sure all nuts and bolts are tight along with ensuring no steps were skipped. Enjoy your COBB Tuning Volkswagen MK7 Intake!




Links

Map Notes for Mk7 GTI

Can let you know what parts will work with what map


Volkswagen GTI MK7, MK7.5

The main resource page for MK7 GTI Installation Instructions


Map Notes for Mk7 Golf R

Can let you know what parts will work with what map


Volkswagen Golf R MK7

The main resource page for MK7 Golf R Installation Instructions

Contact Us:

COBB Customer Support

Web Support and Tech Articles: COBB Tuning Customer Support Center

Email: support@cobbtuning.com

Phone support available 9am to 6pm Monday-Thursday. 9am to 4pm Friday (CST)

866.922.3059


return to www.cobbtuning.com

Copyright 2023 © COBB Tuning Products LLC. All Rights Reserved. | www.cobbtuning.com