315450 - Subaru GR/VA Fuel Pump

315450 - Subaru GR/VA Fuel Pump

Subaru Legacy GT 2005 - 2009
Subaru Impreza WRX 2008 - 2014
Subaru WRX STI 2015-2021




The following instructions will assist you through the installation process. Please read them BEFORE beginning the install to familiarize yourself with the steps and tools needed. If you feel you cannot properly perform this installation, we HIGHLY recommend you take the vehicle to a qualified and experienced automotive technician.




Table of Contents






Stock Fuel Pump Removal

  1. With a low (if not almost empty) tank of gas, park the car in a flat level area and allow it to cool down.

  2. Open up the back door of the car.




  3. Gently lift up on the front of the seat in the center of where one of the passengers would sit.  You should feel an annoyingly sharp handle.  Pull outwards on the handle, it may take a finger on each side of the handle to pull it.  While pulling outward gently lift upward on the seat.  It should pop free.

        


  4. With the front loose gently push down on the back side of the seat near the corner and pull toward the front of the car.  The rear seat should come free


  5. Repeat this process on the other side.


  6. Using a Phillips screwdriver remove the four screws holding the pump cover in place.






  7. Start the car up and allow it to idle.  

  8. Remove the electrical connector by gently squeezing the release tab.






  9. Once the car dies, turn it off, and remove the gas cap.

  10. Using a 10mm wrench, disconnect the battery cables.

  11. At this point it may be helpful to mark the hoses so you know where they go back to.




  12. Gently squeeze the white clips to remove all three hoses in turn.




  13. Now undo the six eight bolts holding down the tank ring using an 8mm socket.

  14. Now go ahead and pull the pump free from the car.




Fuel Pump Disassembly

  1. Move the pump to a well ventilated work area that you aren't afraid to get gas on.  Make sure to keep any possible sources of fire or electrical shocks away from the vicinity to avoid fires.




  2. Unplug the two wiring harnesses from the top hat and take the wiring out of the guides so they're only connected to the bottom half of the fuel pump assembly.








  3. There are multiple clips holding the bucket onto the pump assembly.  You'll want to gently lever them upwards to release the bucket, typically using multiple screwdrivers at the same time will allow you to get all of them loosened and remove the bucket




  4. You should now be left with the bottom half of the pump hanger.



  5. Gently compress the top hat down on the bottom portion to reveal the support rods.  Using a small flathead screwdriver or pick, remove the e-clip holding the fuel pump assembly together.






  6. Set the clip and spring aside in a safe spot as you'll use those later on reassembly.




  7. Unplug the harness from the top of the pump housing.




  8. Pop the two clips holding the two hoses to the bottom of the pump hanger as well.








  9. Make sure the o-rings come out as well, if not fish them out wiht a screwdriver and re-instal them to their respective fitting.



  10. Getting the fuel pump out can be a bit of a pain.  The easiest way is to first remove the wiring harness from the pump by gently depressing the small release tab.  Then using a screwdriver in the side windows or top windows to release the two barbed tabs on the pump from the pump housing and get the pump out.  Be patient as damaging this too much can cause the pump to not be held in place, necessitating a replacement.







  11. Once release from both barb fittings it should slide out






Fuel Pump Assembly

These next steps may vary slightly depending on the manufacturer of your pump, for appropriate specific instructions refer to the manufacturer of your pump.

  1. Move the plastic clip from the stock pump output to the new one.




  2. Add a little bit of lube to the two new o-rings and push them on to the new pump.




  3. Gently push the new pump in to the basket, it will take a little bit of force to get the pump inside but it's important to make sure the output and connector are lined up with the proper positions of the basket.

  4. Remove the plug from the new strainer




  5. Push the new strainer on to the pump and basket assembly.  Using a pair of pliers push down on opposite sides of the clip to retain the strainer onto the pump.




  6. Install the fuel pump side of the wiring but don't plug it back into the top hat yet.



  7. Pop the basket back into the hanger making sure it's going back together in the correct orientation.  Reinstalling the e-clip and springs onto the support rod to retain it in place.




  8. Re-install the two hoses onto the bottom of the fuel pump hanger.






  9. Make sure the bottom of the fuel pump hanger lines up with the hole in the basket as you install it.




  10. Once you're satisfied you can go to reinstall the pump back into the car.

  11. Reinstall the hanger, lines and seat in the reverse order of removal.




CARB Sticker Application

(Where Applicable)

  1. Apply the supplied CARB sticker in a clear, easy to find location.  Typically underhood, or on the radiator core support.







Contact Us:

COBB Customer Support

Web Support and Tech Articles: COBB Tuning Customer Support Center

Email: support@cobbtuning.com

Phone support available 9am to 6pm Monday-Thursday. 9am to 4pm Friday (CST)

866.922.3059


return to www.cobbtuning.com

Copyright 2024 © COBB Tuning Products LLC. All Rights Reserved. | www.cobbtuning.com