Part Number – Part Name

Vehicle Coverage

[placeholder]

Congratulations on your purchase of the COBB Tuning xxxxxxxxxxxxx! The following instructions will assist you through the installation process. Please read them BEFORE beginning the install to familiarize yourself with the steps and tools needed. If you feel you cannot properly perform this installation, we HIGHLY recommend you take the vehicle to a qualified and experienced automotive technician.

IMPORTANT! Installing this kit will require custom tuning or utilizing an appropriate Stage Power Package map if you have a matching mechanical configuration. Please consult with COBB or an authorized ProTuner in your area if you have any questions!

Table of Contents

Parts List

Tools Needed

Sockets

3/8"

• 3/8" ratchet

• 3/8" 12" extension

• 3/8" 6" extension
  

• 3/8" Socket Swivel

• 3/8" 7mm socket

• 3/8" 8mm socket 

• 3/8" 10mm socket

• 3/8" 11mm socket 

• 3/8" 12mm socket 

• 3/8" 13mm socket
  

• 3/8" 14mm socket
  

• 3/8" 16mm socket
• 3/8" 17mm socket
• 3/8" 18mm socket
• 3/8" 19mm socket
• 3/8" 21mm socket

• 3/8" 10mm deep socket

• 3/8" 12mm deep socket 
  

• 3/8" 13mm deep socket

• 3/8" 14mm deep socket
• 3/8" 15mm deep socket

• 3/8" 17mm deep socket

• 3/8" 14mm swivel socket
  

• 3/8" T20 Torx Bit

• 3/8" T25 Torx Bit

• 3/8" T30 Torx Bit

• 3/8" T40 Torx Bit

• 3/8" T50 Torx Bit
• 3/8" E10 inverted Torx
• 3/8" E12 inverted Torx
• 3/8" E14 inverted Torx
• 3/8" E18 inverted Torx
  
• 3/8" 4mm Allen Socket
  
• 3/8" 5 mm Allen Socket
• 3/8" 10 mm Allen Socket
  
  

1/2"

• 1/2" ratchet

• 1/2" breaker bar*
• 1/2" 16" extension*
• 1/2" 14mm socket*
• 1/2" 23mm deep socket
• Torque Wrench

Hand Tools

• Phillips head screwdriver
• Flathead screwdriver
• 3mm Allen Key
• 7mm Nut Driver
• Trim removal tool

• Pick

• Needlenose pliers

• Channel Lock Pliers

• Deadblow Hammer

Misc.

• 14mm offset wrench
• Oxygen Sensor Wrench
• Hose cutter
• Drain pan
• Spill-Free coolant bleeding funnel

Wrenches

• 8mm Ratcheting combination wrench
• 10mm combination wrench
• 11mm combination wrench
• 12mm combination wrench
• 13mm combination wrench
• 14mm combination wrench
• 15mm combination wrench
• 16mm combination wrench
• 17mm combination wrench
• 18mm combination wrench
• 19mm combination wrench
• 21mm combination wrench

Remove Factory Heatshield

Turbo Heat Shield Installation

1. Hand install one of the supplied 10mm bolts along with a washer into the lower up-pipe/turbo support bracket.
   
           
   
   
   
2. Slide the heat shield into place with the cutout over the loosened bolt on the lower mount.
   
   
   
   
   
3. Loosely install the other two bolts on the top and inside of the heat shield.
   
              
   
   
   
4. Slide the heat shield around a little bit to make sure the wastegate arm isn't hitting the bracket and then tighten down each bolt with a 10mm socket.
   
       
   
   
5. Reinstall the intercooler in the reverse order of removal.
   
   
6. Go out and enjoy!

Links

Subaru Map Notes