8F2650 Ford 2.3l Turbo Blanket
Ford Ecoboost Mustang 2014 - 2019
Ford Focus RS 2017 - 2018
Congratulations on your purchase of the COBB Tuning Turbo Blanket! The following instructions will assist you through the installation process. Please read them BEFORE beginning the install to familiarize yourself with the steps and tools needed. If you feel you cannot properly perform this installation, we HIGHLY recommend you take the vehicle to a qualified and experienced automotive technician.
Table of Contents
| Table of Contents |
|---|
Parts List
- COBB Turbo Blanket
- (2) Springs
- Safety wire
Tools Needed
Sockets
3/8"
Hand Tools
Stock Heatshield Removal (Ecoboost Mustang First Step)Ecoboost Mustang Pereparation
| Note |
|---|
While we show one way of wrapping the wire and using springs to secure the turbo blanket there are many different possibilities and options that will work so use the one that works for you while keeping things secured! |
- Using a 13mm socket remove the top two turbo mounting bolts holding the top of the heat shield in place.
- Remove the 13mm bolt holding the damper on to the engine mount. While not strictly necessary, it does give you a little bit more room to try and get the lower heat shield bolt out.
- Remove the T-25 lower bolt attaching the heat shield in place. If it stripped like ours, removing the motor mount will allow additional room to get in there and work at getting it off of the car.
Focus RS Preparation
- Remove the plastic engine cover by gently pulling up. It is merely held down by pressure clips.
- Remove (2) Torx bolts securing down the front of the front windshield cowl using a Torx bit. There will be a bolt on the driver's side and on the passenger's side of the engine bay.
- Remove (4) pressure clips securing the front windshield cowl using a flathead screwdriver.
- Gently pull up and release the (2) debris covers on the front windshield cowl. There will be one on the driver's side and one on the passenger's side.
- Remove the (2) ?mm bots securing the the debris/water guard under the front windshield cowl. There will be one on the driver's side and one on the passenger's side.
- Remove the rubber cover off of each windshield wiper to access the 15mm nut underneath. Remove each wiper. Remember which side is which for reinstallation later.
- Remove the debris guard and windshield Cowl.
- Loosen the (2) hose clamps connecting the two sides of the intake pipe using an 7mm socket.
- Loosen the single hose clamp securing the intake pipe to the airbox using an 7mm socket.
- Loosen the single hose clamp securing the intake pipe to the turbo using an ?mm socket.
- Remove the rubber grommet from the mounting location securing the electrical harness to the intake pipe.
- Disconnect the PCV plug from the back of the intake pipe. You may need to gently lift up the the front windshield cowl to gain access to the plug.
- Gently lift and remove the stock intake system from the car. Be wary of any electrical cables or vacuum hoses that may be in the engine bay as you're removing the piping.
- Moving under the car remove the 4 trim clips from the fabric undertray using your trim tool.
- Using a T30 torx bit remove the 8 torx screws holding the remaining portion of the undertray to the car and drop it out of place.
Turbo Blanket Installation
- This is how your blanket will sit over the turbo, slide the lower section under the wastegate bracket and up around the back towards the front.
- Once it's about in place loop a piece of wire around the lower rivet in order to more easily pull it up around the bottom of the turbo.
- Connect the rivet from the rear lower section up to the bottom of the top piece using either a spring or some of the wire.
- Now connect the rivet on the rear side around the front of the blanket to the rivet on the left side.
- Now tuck the corners under the bolts and you're done! Alternatively you can also re-install the factory heat shield, but depending on where the fabric is bundled, it may not fit any longer.
Important Notes
While not flammable on their own, if any sort of flammable chemical gets into the fiber of the turbo blanket, it may be possible for a fire to occur. It is recommended to replace the turbo blanket if ANY flammable chemicals, liquids, or materials get on the blanket.
Links
| Insert excerpt | ||||||
|---|---|---|---|---|---|---|
|